Panasonic KX-P7100 Скачать руководство пользователя страница 38

Страница: 38 / 148

3.11. Fuser Unit

Before performing the following steps, remove the upper Exit Roller Holder ( see Section 3.10 ).

(1) Disconnect connector CN9 on the Main Controller Board.

(2) Disconnect the connector CN202 from the Power Supply

Unit.

(3) Disconnect the connector CN407 from the Relay Board (B).

(4) Remove the 4 screws.

(5) Remove the Fuser Unit.

3.11.1. Fuser Unit Disassembly

(1) Remove the Lower Exit Roller Gear.

(2) Remove the 2 black screws.

(3) Separate the Heat Roller Holder from the Fuser Unit Base.

(4) Remove the Pressure Roller, 2 bushings, 2 springs and

Lower Exit Roller from the Heat Roller Holder.

(5) If necessary, remove the Pinch Rollers and Cleaning

Rollers.

Caution:

When reinstalling the Pinch Roller and Spring,
the spring hook is attached upward to prevent
any damage to the printing media as shown
following figure.

When

reinstalling

the

Cleaning

Roller

and

Spring, the spring hook is attached downward
and the cut edge of the cleaning roller is located
as

shown

following

figure

to prevent any

damage to the Pressure Roller.

KX-P7100

Содержание KX-P7100




















































































































































Результаты поиска

Содержание KX-P7100

Отзывы:

Похожие инструкции для KX-P7100

Бренды по названию

Популярные бренды

Panasonic KX-P7100, Руководство по обслуживанию

Результаты поиска

Содержание KX-P7100

Отзывы:

Похожие инструкции для KX-P7100

Бренды по названию

Популярные бренды