Panasonic KX-P7100 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 148

background image

1.10. Fuser Unit

A 600W heat lamp ( halogen lamp ) heats the surface of the teflon-coated heat roller to approximately 190°C ( 374°F ), a thermistor
monitors the heat roller temperature, and the CPU controls the ON/OFF timing of the lamp.

The thermostat is mounted 2.5mm away from the heat roller. If the ambient temperature reaches 180°C ( 356°F ), the thermostat
is opened, and power is removed from the heat lamp. The surface of the thermostat is not as hot as thatof the heat roller. When
the thermostat opens, the surface of the heat roller may reach 200°C ( 382°F ), and the system displays E30. If the thermistor
opens, the system displays E32. If by chance the thermostat malfunctions a thermalfuse opens.

The pressure roller is kept in contact with the heat roller through 2 pressure springs, which apply a pressure of approximately 0.36
kg/cm ( 3.56 N/cm ). Drive is supplied from the main motor via intermediate gears.

20

KX-P7100

«
...
18
19
20
21
22
...
»

Содержание KX-P7100





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-P7100

Pixma MG2400 Series

Бренд: Canon Страницы: 2

Бренд: LabelTac Страницы: 2

Бренд: Ier Страницы: 8

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 4

Бренд: Datecs Страницы: 73

Бренд: Datamax Страницы: 12

E-Class Mark II

Бренд: Datamax Страницы: 40

Бренд: Datamax Страницы: 46

Бренд: YAEN Страницы: 4

Бренд: Zonestar Страницы: 25

Бренд: Xerox Страницы: 8

Бренд: Savin Страницы: 4

Бренд: Konica Minolta Страницы: 424

Бренд: MIMAKI Страницы: 28

Jetrix LXi Series

Бренд: InkTec Страницы: 3

Бренд: Xerox Страницы: 284

Adaptive CMYK+ Kit

Бренд: Xerox Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды