Panasonic KX-FPC135 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 264

background image

2.2. USER RECOVERABLE ERRORS

If the unit detects a problem, one or more of the following messages will appear on the display.

[ This error is displayed when the thermal head does not warm up. Check the thermistor

on the thermal head and connector lead. (for technicians)]

[ The backup battery on the top of the digital board may be low or dead, so check it.]

Trademark
is a registered trademark of FaxSav Incorporated.

R

[Refer to 1.8. FEATURES for details on the

service.]

R

Display message

Cause & Remedy

MEMORY FULL

LOADING ERROR

JOG-DIAL FULL

FREE FILM EMPTY

FILM NEAR EMPTY

FILM EMPTY

FAX MEMORY FULL

FAX IN MEMORY

CHECK PAPER

CHECK MEMORY

CHECK FILM

CHECK DOCUMENT

CHECK COVER

CALL SERVICE

There is something wrong with the unit. Contact our service personnel.

The cover is open. Close it.

The document is not fed into the unit properly. Reinsert the document. If
misfeeding occurs frequently, clean the document feeder rollers and try again
(p. 132). If the problem remains, adjust the feeder pressure.

The film cartridge is not installed. Install it.

Memory (telephone numbers, parameters, etc.) has been erased. Re-program.

The recording paper is not installed or the unit has run out of paper. Install
paper and press

to clear the message.

The recording paper is not fed into the unit properly or has jammed near the
recording paper entrance. Clear the jammed paper and press

to clear the message.

Do not install folded or heavily curled paper in the paper tray.

The unit has a document in memory. See the other displayed message
instructions to print out the document.

Memory is full of received documents due to a lack of recording paper or a
recording paper jam etc. Install paper or clear the jammed paper.
When performing memory transmission, the document being stored exceeds
the memory capacity of the unit. Transmit the entire document using manual or
automatic transmission.

The film is empty. Replace the film cartridge.
The film is slack. Tighten it and install again.

The remaining film can print about 15 pages of letter size document. Prepare a
new film cartridge.

The free starter film is empty. Replace the film cartridge.

There is no space to store new stations in the JOG DIAL directory. Edit or erase
unnecessary stations.

A loading error occurred while receiving data from FaxSav.

When making a copy, the document being stored exceeds the memory capacity
of the unit. Press

to clear the message.

STOP

START/SET/COPY

START/SET/COPY

33

KX-FPC135 / KX-FPC141

«
...
31
32
33
34
35
...
»

Содержание KX-FPC135









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FPC135

2 Line KX-TG9541C

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 2

Бренд: Necchi Страницы: 40

Бренд: Singer Страницы: 100

Бренд: Tennant Страницы: 16

Бренд: Duerkopp Adler Страницы: 35

Бренд: Matrix Fitness Страницы: 26

Jem Platinum 720

Бренд: Janome Страницы: 41

PowerBoss AM7D-III

Бренд: HAKO Страницы: 84

Бренд: Kärcher Страницы: 12

Бренд: Bernina Страницы: 134

Бренд: Janome Страницы: 43

ULTRA-STITCH SM-1100

Бренд: Mueller Страницы: 28

Hard Floor Cleaner

Бренд: Prolux Страницы: 20

Бренд: Singer Страницы: 56

Бренд: Necchi Страницы: 53

Бренд: JUKI Страницы: 126

Бренд: Pacific Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды