Panasonic KX-FPC135 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 264

background image

3.6. Objective

This procedure will enable the technician to make adjustments
to the KX-FPC135/KX-FPC141 HANDSET and BASE UNIT.

3.7. General Information

This procedure has 2 sections. The first section instructs the
technician on how to align the HANDSET. We recommend
aligning the HANDSET first, since you will need the HANDSET
to align the BASE UNIT. The second section aligns the BASE
UNIT. You can use either section separately, or together to
align the entire cordless phone unit.

At the beginning of each section, you will find a preparation
procedure instructing you on how to prepare the unit to the
point of placing the unit in TEST mode. Please follow this
procedure to insure proper alignment.

Each section´s procedure consists of Adjustment Items
adjusting one specific variable hardware component.
Each Item lists the equipment needed, how to connect and
setup the equipment, how to make the adjustment, and how to
verify the adjustment if necessary.

Before the actual procedure, you will find a procedure detailing
how to place that part in TEST mode. You will have to perform
this procedure before each individual Adjustment Item.

Once aligned, please remove all equipment connections and
solder points, and reassemble the unit. As a final check, power
up the phone and check for HANDSET linking with the BASE
UNIT.

3.8. Equipment

1. Radio Tester : Marconi Model 2295A or later.

2. 4.5 digit Digital Multimeter : B&K Model 2833 or compatible.

3. Oscilloscope, single or dual channel : Panasonic VP-

5512P100 or compatible.

4. Telephone Analyzer : B&K Model 1050 or compatible.

5. DC Power Supply, capable of supply 3.9V DC at 100mA

NOTE : only needed if Telephone Analyzer does not have
DC VOLTS output available.

6. Corded Telephone.

7. High Frequency Cable : BNC end to open end.

8. Audio Cable : BNC end to alligator clip end.

9. High Frequency Adjustment Tool:

10. Isolation Capacitors, quantity of 2, 10 µF maximum, 50V

DC or greater.

11. Soldering Iron, solder, and various tools.

3.9. Handset Preparation

Please perform the following steps to prepare the HANDSET
for alignment. Please refer to the HANDSET REFERENCE
DRAWING for connection and test point locations.

1. Remove battery cover and battery.

2. Remove both screws at the case bottom.

3. Grabbing hold of the back near the bottom, gently pry off

the back of the case.

4. Remove the antenna mounting screw. Pull out the antenna.

5. Unsolder both speaker connections on P.C.Board.

6. Remove the HANDSET P.C.Board.

7. Remove the keypad membrane.

8. Solder High Frequency Cable open end to ANT and RF

GND points.

9. Using the Digital Multimeter, measure DC VOLTS output on

the Telephone Analyzer. Adjust the output voltage to 3.9V
DC.

10. Solder battery connection wires at the points shown in the

HANDSET REFERENCE DRAWING. Solder the positive
lead to TP-V

DD

, towards the component side of the

P.C.Board. Solder the negative lead to the TP-V

SS

. DO

NOT APPLY POWER TO THE HANDSET AT THIS
TIME!!!!!!

11. Solder a small, insulated piece of wire to GND as well.

12. Solder 1 isolation capacitor´s positive lead to SP+ test

point. When soldering, keep the lead close to the
P.C.Board as possible since you will lay the keypad
membrane over part of this lead.

13. Solder a small, short, insulated wire to MIC test point.

14. Lay the keypad membrane over the keypad

switch

contacts.

3.10. Symptom/Remedy Table

If you have one of the listed symptoms, please refer to this
table and make the appropriate adjustments.

3.11. Handset Adjustment

Preparation

Please perform the following procedure before starting the
Adjustment

Procedure.

You

only

have

to

perform

this

procedure only once to complete all Items, but you will have to
perform this procedure to make an individual Adjustment Item.

1. You

will

need

all

equipment

listed

in

the

Item´s

EQUIPMENT section.

2. Setup

all

equipment

as

specified

in

the

Item´s

PROCEDURE section SETUP portion.

3. Apply power to the HANDSET, and press TALK key.

4. Press 5, 8 and 0 keys at the same time.

5. You should hear the HANDSET beep. Release the 3 keys.

If you do not hear a beep, remove the power from the
HANDSET and repeat the last 2 steps.

6. Press the TALK key. HANDSET should now be in TEST

MODE (CH 1 TALK). The TALK should be on. If the
HANDSET is not in TEST MODE, remove the power and
repeat the last 3 steps.

7. Remove the keypad membrane and lay it aside to prevent

pressing some button by mistake during alignment.

127

KX-FPC135 / KX-FPC141

«
...
125
126
127
128
129
...
»

Содержание KX-FPC135









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FPC135

Бренд: Adler Страницы: 20

Бренд: Duerkopp Adler Страницы: 35

Бренд: Kärcher Страницы: 9

Бренд: Janome Страницы: 40

Бренд: CIMLINE Страницы: 60

Бренд: JUKI Страницы: 4

AMS-221EN Series

Бренд: JUKI Страницы: 253

Бренд: JUKI Страницы: 59

Бренд: Bosch Страницы: 17

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 52

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 48

Бренд: Brother Страницы: 42

Бренд: Canon Страницы: 65

Бренд: Canon Страницы: 17

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 185

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды