Panasonic KX-FPC135 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 264

background image

1.13. CONNECTIONS

1.13.1. CONNECTIONS (KX-FPC135)

This connection is for the U.S.A. version only. Refer to the simplified manual (cover) for other areas.

Automatic dialing mode setting

When the telephone line cord and the power cord are connected, the unit will automatically start to detect
the dialing mode of your telephone line.

Display:

Wait until one of the following messages is displayed.

Your line has touch tone service.

Your line has rotary pulse dial service.

If the power cord is disconnected or a power failure occurs, the unit will detect the dialing mode again when
power is restored.
If you connect the power cord before connecting the telephone line cord, the following messages will be
shown alternately.

Connect the telephone line cord.

(Model KX-FPC135)

INSERT TEL LINE

NO TEL LINE

LINE IS PULSE

LINE IS TONE

CHECKING LINE

Wall jack
(RJ11C)

120 V, 60 Hz

Telephone
line cord

Power cord

Power surge
protector

( )

Line surge
protector

( )

Connect to “LINE”.

1

Connect the telephone line cord.

2

Connect the power cord.

The unit will automatically start to
detect the dialing mode of your
telephone line (see below).

When the power is turned on for the
first time, the unit will print some
basic information.

Note:

For additional equipment protection, we recommend the use of a surge protector. The following types are
available; TELESPIKE BLOK MODEL TSB (TRIPPE MFG. CO.), SPIKE BLOK MODEL SK6-0 (TRIPPE
MFG. CO.), SUPER MAX (PANAMAX) or MP1 (ITW LINX).
The warranty does not cover damage due to power line surges or lightning.
When
If you went to connect an answering machine to the unit.

you operate this product, the power outlet should be near the product and easily accessible.

2

1

16

KX-FPC135 / KX-FPC141

«
...
14
15
16
17
18
...
»

Содержание KX-FPC135









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FPC135

PIXMA MX882 Series

Бренд: Canon Страницы: 80

MultiPASS C3500

Бренд: Canon Страницы: 47

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 212

Бренд: IDEAL Страницы: 36

Бренд: Janome Страницы: 5

Бренд: W6 Страницы: 48

Embroidery Mode-Stitch-Out

Бренд: Pfaff Страницы: 10

Бренд: Carina Страницы: 30

Бренд: DIAKAT Страницы: 11

Бренд: Renkforce Страницы: 52

Бренд: Alto Страницы: 51

SWEEPER VAC V-036

Бренд: Vax Страницы: 12

Бренд: Olivetti Страницы: 76

Office Bridge IF-200

Бренд: Muratec Страницы: 41

Бренд: Brother Страницы: 36

Бренд: Brother Страницы: 83

Бренд: Brother Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды