Panasonic KX-FPC135 Скачать руководство пользователя страница 130

Страница: 130 / 264

4 HOW TO CHECK THE RF

UNIT

Factory supply only assembled RF unit for base unit and
Handset of KX-FPC135/KX-FPC141. (Factory does not supply
each parts on RF Unit.)

4.1. Handset

1. Warm up the Marconi Radio Tester for at least 30 minutes

to allow internal crystal oscillation to become stable.

2. Refer to figures right for Handset wire connections.

3. Disconnect the Handset antenna from the PCB. If you allow

the antenna to remain and be a load, the readings will be
wrong.

4. Supply DC 3.9V Handset PCB using a DC power supply.

5. Solder RF cable to TP-ANT and TP-GND and connect BNC

side to Marconi. Use 100 W max. RF Input.

6. Press TALK, then press "5", "8" and "0" simultaneously.

7. Press TALK. (Base Unit power is off)

4.1.1. Carrier frequency check:

1. Set Marconi to Transmit Test (press TX TEST button).

2. Check TX Frequency =926.100 MHz+/-3.0 kHz.

3. When value if off, adjust VRfreq.

4. If can´t adjust replace RF Unit.

4.1.2. Transmit power check:

1. Press dBm button on Marconi.

2. Check Marconi TX Power reading. It should equal

-3.5 dBm+/-4 dBm (-7.5 dBm ~ +1.5 dBm).

3. When value is over, replace RF Unit.

4.1.3. Receiving sensitivity check:

1. Connect audio cable BNC side to AF INPUT in Marconi and

other side to TP-AF and TP-GND.

2. Set Marconi to RX TEST mode. Enter the following setting:

a. Frequency = 902.100 MHz

b. Level = 60 dBµV

Set Modulation = 1.000 kHz

d. Level = 6.000 kHz

3. Press the SINAD button on Marconi until the display shows

SINAD value. Press the dB button.

4. Press the RF GEN and LEVEL button.

5. Using the VARIABLE knob on Marconi decrease RF GEN

LEVEL value until SINAD value is 12 dB.

6. Check the RF GEN LEVEL. This should be less than

+1 dBµV(+7 dBµVemf). When value is over, replace RF
Unit.

4.1.4. Squelch check:

1. Connect scope probe (X1) lead to TP-SQ, negative to TP-

VSS and BNC end to scope.

2. Set scope to the following codition: TIME/DIV = 1 msec,

VOLT/DIV = 1 V

3. Set RF GEN LEVEL to +5 dBµV(+11dBµVemf). Check

scope voltage is LOW.

4. Set RF GEN LEVEL to -17 dBµV(-11dBµVemf). Check

scope voltage is HIGH.

5. When scope voltage is wrong, replace RF Unit.

130

KX-FPC135 / KX-FPC141

Содержание KX-FPC135









































































































































































































































































Результаты поиска

Содержание KX-FPC135

Отзывы:

Похожие инструкции для KX-FPC135

Бренды по названию

Популярные бренды

Panasonic KX-FPC135, Руководство по обслуживанию

Результаты поиска

Содержание KX-FPC135

Отзывы:

Похожие инструкции для KX-FPC135

Бренды по названию

Популярные бренды