Panasonic KX-FP342CX Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 247

background image

(3) YOUR LOGO
The user logo recorded in the unit. If it is not recorded, NONE will be displayed.
(4) YOUR TELEPHONE NUMBER
The user telephone number recorded in the unit. If it is not recorded, NONE will be displayed.
(5) FAX PAGER NUMBER
If you program a pager number into the unit, the pager number will be displayed here.
(6) FACTORY - CUSTOMER
This shows how many days from factory production until the user turns ON the unit.
(7) MONTH
The shows the very first month, date, year and time set by the user after they purchased the unit.
(8) DAY
The shows the very first month, date, year and time set by the user after they purchased the unit.
(9) YEAR
The shows the very first month, date, year and time set by the user after they purchased the unit.
(10) TIME
The shows the very first month, date, year and time set by the user after they purchased the unit.
(11) USAGE TIME
The amount of time the unit has been powered ON.
(12) FACTORY - NOW
This shows how many days from factory production until the user prints out this history list.
(13) TEL MODE
The amount of time the TEL mode setting was used.
(14) FAX MODE
The amount of time the FAX mode setting was used.
(15) Not Used
(16) ANS/FAX MODE
The amount of time the ANS/FAX mode setting was used.
(17) FINAL RECEIVE MODE
The last set receiving mode by the user.
(18) TONE/PULSE SELECTION
The most recently used setting used, either TONE or PULSE.
(19) RECEIVE REDUCTION
The compression rate when receiving.
(20) SETTING NO. OF DIRECTORY
The recorded directory stations.
(21) NUMBER OF COPY
The number of pages copied.
(22) NUMBER OF RECEIVE
The number of pages received.
(23) NUMBER OF SENDING
The number of pages sent.
(24) NUMBER OF CALLER ID
The number of times Caller ID was received.
(25) NUMBER OF RECORDING MESSAGE
The number of messages recorded in TAM.
(26)~(29) Not Used
(30) NUMBER OF PRINTING WARNING LIST
The number of warning lists printed until now.
(31) NUMBER OF PRINTING HELP
The number of help lists printed until now.

81

«
...
79
80
81
82
83
...
»

Содержание KX-FP342CX
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FP342CX

Бренд: Janome Страницы: 2

Бренд: Janome Страницы: 75

Бренд: Janome Страницы: 40

Бренд: Janome Страницы: 45

Бренд: Janome Страницы: 51

Бренд: Janome Страницы: 2

MEMORY CRAFT 9700

Бренд: Janome Страницы: 110

Memory Craft 3000

Бренд: Janome Страницы: 42

Memory Craft 10001

Бренд: Janome Страницы: 181

Бренд: Janome Страницы: 41

Бренд: Janome Страницы: 32

Бренд: Necta Страницы: 48

Бренд: Singer Страницы: 8

Бренд: Fastbind Страницы: 21

Бренд: Pfaff Страницы: 122

Бренд: Fortis Страницы: 12

Бренд: easymaxx Страницы: 2

Бренд: Dixie Narco Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды