Panasonic KX-FP105RS, Руководство по обслуживанию

Страница: 16 / 43

2.5. SERVICE FUNCTION TABLE
Change from original pages 84, 85 (2.4.4. SERVICE FUNCTION TABLE)
Code Function Set Value Effective Range Default Remarks
501 Pause time set X 100 msec 001~600 50 ----------
502 Flash time set X 10 msec 01~99 70 ----------
503 Dial speed select 1:10 pps 2:20 pps 1, 2 1 ----------
511 Vox sense 1:High 2:Low 1, 2 1 When the TAM (or EXT TAM) does not
stop recording the ICM because noise is
detected on the telephone line, change
this setting to "LOW".
520 CED frequency select 1:2100 Hz 2:1100 Hz 1, 2 1 See Symptom/Countermeasure Table
for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table
for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when
transmission is complete.
523 Receive equalizer select 1:0.0km 2:1.8km
3:3.6km 4:7.2km 1~4 1 When the telephone station is far from the
unit or reception cannot be performed
correctly, adjust accordingly.
524 Transmission equalizer select 1:0.0km 2:1.8km
3:3.6km 4:7.2km 1~4 1 When the telephone station is far from the
unit or reception cannot be performed
correctly, adjust accordingly.
550 "Memory clear: To reset the value to the default one, except the top margin (853) and left
margin (854)." “START” input
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See 2.5. TEST FUNCTIONS.
553 Monitor on FAX communication
select 1:OFF
2:PHASE B
3:ALL 1~3 1 Sets wherher to monitor the line signal
with the unit´s speaker during FAX
communication or not.
554 Modem test See 2.5. TEST FUNCTIONS.
555 Scan check See 2.5. TEST FUNCTIONS.
556 Motor test 0 See 2.5. TEST FUNCTIONS.
557 LED test See 2.5. TEST FUNCTIONS.
558 LCD test See 2.5. TEST FUNCTIONS.
559 Document jam detection select 1:ON 2:OFF 1, 2 1 See 2.2.1. Paper Jam.
561 KEY test See 2.5. TEST FUNCTIONS.
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing
according PBX.
571 ITS auto redial time set X number of times 00~99 14 Selects the number of times that ITS is
redialed (not including the first dial).
572 ITS auto redial line disconnection
time set X second 001~999 30 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of rings 01~99 15 Sets the number of rings before the unit
starts to receive a document in the TEL
mode.
590 FAX auto redial time set X number of times 00~99 5 Selects the number of redial times during
FAX communication (not including the first
dial).
591 FAX auto redial time disconnection
time set X second 001~999 45 Sets the FAX redial interval during FAX
communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO 1~3 2 Lets you select the CNG output during
FAX transmission.
ALL: CNG is output at phase A.
AUTO: CNG is output only when
automatic dialing is performed.
OFF: CNG is not output at phase A.
593 Time between CED and 300bps 1: 75 msec
2:500 msec
3:1 sec 1~3 1 See Symptom/Countermeasure Table
for long distance and international calls in
2.3.3.1. Defective Facsimile Section.
594 Overseas DIS detection select 1:detects at the 1st time
2:detects at the 2nd time 1, 2 1 See Symptom/Countermeasure Table for
long distance and international calls in
2.3.3.1. Defective Facsimile Section.
595 Receive error limit value set X Number of times 001~999 100 Sets the number of acceptable error lines
when the FAX reconstructs the received
data.
596 Transmit level set X dBm - 15~00 -10 Selects the FAX transmission level.
598 Receiving sensitivity 43= -43 dBm 20~48 43 Used when there is an error problem.
599 ECM frame size 1:256 2:64 1, 2 1 See 2.2.1. Paper jam
602 Warning LIST Printing 1:ON 2:OFF 1, 2 1 Used to print a caution list when setting
the TEL/FAX mode and ring detection.
700 EXT. TAM OGM Rec.time X second 01~99 10 Set the start time of silent detection.
16
KX-FP105RS