Panasonic GT02 Скачать руководство пользователя страница 22

Страница: 22 / 67

3.1.7 Error Codes

The error codes are as follows.

Error codes
For GT01, GT11 and GT21

Error code

Error name

Measures

ER00

BCC error

The value of BCC may be incorrect. Check if there is no
calculation mistake.

ER01

Format error

A command format may be incorrect. Check if it is correct.

ER02

NOT supported error

A command used is not supported with the version of the
GT. Upgrade the version of the GT, or use another
command.

ER03

Address error

The address specified does not exist in the GT. Check the
address of the transmitted command.

ER04

Receive buffer overflow

The sent command exceeds the receivable number of
bytes. Check the number of bytes of the sent command.

ER05

Requested overflow

The sent readout command exceeds the number of bytes
that can send back. Check the number of the read words.

ER06

Data error

The communication condition for the GT may be
unmatched with the condition for a destination device.
Check the communication conditions.

ER07

Data write inhibit error

A command for the address that writingn is not available
was sent. Check the address of the sent command.

For GT02, GT02L, GT05, GT12, GT32 and GT32-E

Error code

Error name

Measures

**0000

BCC error

The value of BCC may be incorrect. Check if there is no
calculation mistake.

**0001

Format error

A command format may be incorrect. Check if it is correct.

**0002

NOT supported error

A command used is not supported with the version of the
GT. Upgrade the version of the GT, or use another
command.

**0003

Address error

The address specified does not exist in the GT. Check the
address of the transmitted command.

**0004

Receive buffer overflow

The sent command exceeds the receivable number of
bytes. Check the number of bytes of the sent command.

**0005

Requested overflow

The sent readout command exceeds the number of bytes
that can send back. Check the number of the read words.

**0006

Data error

The communication condition for the GT may be
unmatched with the condition for a destination device.
Check the communication conditions.

**0007

Data write inhibit error

A command for the address that writingn is not available
was sent. Check the address of the sent command.

Note) These are the error codes related to communicaiton.

3.1.8 Restrictions

Allowable bytes sent and received

The allowable number of bytes to be sent and received in the GT is up to 512 bytes (including CR).
Therefore, a command or response of which size is more than 513 bytes cannot be sent from the
external device.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание GT02




































































Результаты поиска

Содержание GT02

Отзывы:

Panasonic GT02, Руководство пользователя, Страница: 22 / 67

Результаты поиска

Содержание GT02

Отзывы: