Panasonic GT02 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 67

Panasonic GT02 Скачать руководство пользователя страница 18

3.1 What is Command Response Mode

3.1.1 Overview of Communication Mode

In the command response mode, once a command is sent to the GT from an external device, a response
will be sent back to the external device from the GT.
The GT always sends back a response when it received a command. When any response is not sent
back, check if the connection of the communication cable is correct or the sent command is correct.

3.1.2 Setting Communication Conditions

•

Specify the unit numbers within a range of 00 to 63. When making 1:n connection with the external

device, do not specify the same unit number for multiple GTs.

•

The settings for "Baud rate", "Data length" and "Parity check" should be the same as the

communication settings specified on the external device.

•

It is not necessary to use the CS/RS control signals in the command response mode. When connecting

an external device that does not control them, short-circuit the "RS" and "CS" terminals of the COM
port on the GT side or set "CS/RS Control" to "Off"

Item

Settings

Caution

Unit number

00 to 63

Do not specify the same unit
number for multiple GTs.

Baud rate

115200/57600/38400/19200/9600 bps

These settings should be the same
as the settings specified on the
external device.

Data length

7/8 bits

Stop bits

Fixed: 1 bit

Parity check

Odd/Even/Invalid

CS/RS signal control

No CS/RS signal (GT01)
Fixed: On (GT11, GT21)
On/Off (Other models)

The CS/RS signals are not used in
the command response mode.

Note

)

CS/RS signal (control) is not available for GT01.

Reference:

For the details of the communication parameters of GT, refer to <2.1 Setting on GTWIN>.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
...
16
17
18
19
20
...
»

Содержание GT02




































































Отзывы:

Нет отзывов