Panasonic GT02 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 67

Panasonic GT02 Скачать руководство пользователя страница 15

Communication System

Select a communication system according to the used communication system.
(The RS485 communication can be used in the command response mode only.)

Transmission Delay

The time taken to send the next data from receiving data from an external equipment can be adjusted
with the GT. The delay time longer than the preset value can be held by specifying the time until sending
data. Set it when the external equipment cannot receive data properly as data transmission is too quick
from the GT.

CS/RS Control (GT02, GT02L, GT05, GT12, GT32, GT32-E)

Select either "Off" or "On". When selecting "On", RS(RTS) always outputs LOW and the transmission is
interrupted according to the input status (LOW/HIGH) of CS(CTS). (This setting is available for the
RS232C type.)

Key Point:

GT01 does not have the terminal for CS/RS signal control. When replacing GT01 with GT02, GT02L,
GT05, GT12, GT32 or GT32-E, setting the CS/RS control to "Off" enables to replace the models without
changing the wirings for external devices.

Note:

When "Transfer Data After Clear GT Screen" is performed or "Clear F-ROM" is performed from the
setting mode of the system menu without connecting a CS/RS signal line although the CS/RS control is
set to "On", garbage data is sent to the external device from the GT. (Except GT01, GT11 and GT21)

2.1.4 Transmission of GT Configuration Data

The settings specified in 2.1.1 to 2.1.4 will be effective when the “GT Configuration” data is transferred to
the GT. (The “GT Configuration” data will be automatically transferred once all the data are transferred.)

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
...
13
14
15
16
17
...
»

Содержание GT02




































































Отзывы:

Нет отзывов