background image

4

PLEASE  READ  PRIOR  T O  I N ST A LLI NG  THIS  FAN  CONT I NUED

These fans are also built to take care of the homeowner’s spot ventilation needs when the room is 
occupied. The basic fan models allow a choice of three speeds. When fans are equipped with the optional 
Multi-Speed module, these models increase to a maximum level of 150 CFM for the FV-1115VKL2 and 110 
CFM for the FV-0511VKSL2 and FV-0511VKL2 either when the switch is turned on or activated by the 
optional Condensation Sensor module or the optional Motion Sensor module.

A High/Low Delay Timer, located inside the fan unit, is utilized to return the fan back to the pre-set
continuous ventilation mode. The installer needs to consult with the homeowner for the desired
setting on the timer (0 - 60 minutes) and make the adjustments during the installation.

CustomVent Multi-Speed module (Lower Setting).   ASHRAE 62.2-2016

(sq.feet)

<  500

501-1000

38
53
68
83
98

113
128
143
158

45
60
75
90

105
120
135
150
165

53
68
83
98

113
128
143
158
173

60
75
90

105
120
135
150
165
180

Two Bedrooms Three Bedrooms Four Bedrooms

Five Bedrooms

DoC Responsible Party:

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ 07102

1-866-292-7299

Customer Call Support:

Risk of Fire: Type IC-Inherently Protected.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation.

D ESCRI PT I O N

These products are listed by UL under UL file No. E78414.

These products use a sirocco fan driven by a DC motor powered by an integral transformer. The motor is

designed to have long operating life, high dynamic response, higher speed ranges with saving energy.

The grille covering the fan body is a spring-loaded, quick remove type. A damper for preventing air counter

flow is provided. The blower uses a high-capacity sirocco fan developed to reduce the noise level. The

FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference will not occur in 

a particular installation. If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning this product on and off, the user is encouraged to try to correct the 

interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect equipment into outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning: This equipment m us t be installed by qualified person in accordance with t he provided installation 

instructions; and all applicable codes and standards. Also, any changes or modifications not expressly 

approved by the party responsible for compliance could void the user’s authority to operate this equipment

lighting unit is an energy-saving LED lighting device that uses one 10W LED lamp and produces almost the 

same illumination as a standard 40W incandescent lamp. Night light feature consumes around 0.1 to 0.4 W.

module the fans are built to run continuously at a pre-set lower level (FV-0511VKSL2 and FV-0511VKL2:  
0,30,40, 50, 60, 70, 80, 90, 100 CFM; FV-1115VKL2: 0, 50, 60, 70, 80, 90, 100, 110, 120 CFM). The setting 
is dependent on the size of the house and the individual wishes of the homeowner. It is crucial that the
installer pre-set the lower setting during the installation. Please refer to the chart below and the 

switch indication on page 6. 

English

1001-1500

173

180

188

195

1501-2000

2001-5500
2501-3000

3001-3500
3501-4000

4001-4500
4501-5000

Содержание FV-0511VKL2













Отзывы: