Panasonic FP0-TC4 Скачать руководство пользователя страница 20

Страница: 20 / 24

*1 The measurement range available for degree Celsius is not available for degree Fahrenheit, of which the

upper-limit measurement is set lower than degree Celsius, since the digital value (temperature value

displayed) for degree Fahrenheit is bigger than that for degree Celsius.

*2 When the thermocouple is broken, the digital value will become K8000 or K16000 within 70 seconds

since broken. Practice in the ladder program a process for avoiding a risk, would be resulting from a

broken thermocouple, and exchange the thermocouple.

*3 Until the conversion data will be ready after the initial startup was made, the digital value shows K8001

or K16001. Those are not a temperature data. Create a ladder program, so that they are not acquired as

a temperature data.

*4 The settings of the Input channel selection switch.
*5 Conversion values for 6-time measurements (6 from the latest 8 measurements, excluding the Max. and

Min.) are averaged, so that it takes time for the digital value to be displayed due to the rapid temperature

change.

*6 The Control Unit reads the data for 2 channels per 1 scan by the Control Unit.

Read the data using the program described in 7.2.

*7 This changes depending on where the Thermocouple Unit is installed. (This is when the Thermocouple

Unit is installed in the 1st.)

Insulation outline

Analog input

circuit

PhotoMos relay

channel switch

circuit (insulated

between

channels)

ＦＰ

/ＦＰ０

Control Unit

Ｉ／Ｆ

Photo-coupler

insulation

DC-DC converter

insulation

Bus

+5 V

CH0

CH7

Thermocouple Unit

24 V DC

（Increased
amount 25mA
Max.）

Содержание FP0-TC4

























Результаты поиска

Содержание FP0-TC4

Отзывы:

Бренды по названию

Популярные бренды

Panasonic FP0-TC4, Техническое руководство

Результаты поиска

Содержание FP0-TC4

Отзывы:

Бренды по названию

Популярные бренды