background image

- 9 - 

 

Battery pack

To AC 

outlet

Battery 

charger

  3.  During charging, the charging lamp 

will be lit.

 

  When charging is completed, an 

internal electronic switch will au-

tomatically be triggered to prevent 

overcharging.

 Charging will not start if the battery 

pack is warm (for example, immedi-

ately after heavy-duty operation).

  The orange standby lamp will be 

lit  until  the  battery  cools  down.  

Charging will then begin automati-

cally.

  4.  When charging is completed, the 

charging lamp will start flashing rapidly.

  5.  When in any of the conditions that 

battery pack is too cool, or the bat-

tery pack has not been used for a 

long time, the charging lamp starts 

flashing slowly to indicate protective 

charging.  Protective charging takes 

longer to fully charge the battery 

pack, than the standard charging 

time.  (Max. charging time is ap-

prox. 90 minutes).

 If  a  fully  charged  battery  pack  is 

inserted  into  the  charger  again, 

the  charging  lamp  may  light  up 

and  then  flash  slowly. After  sev-

eral  minutes,  the  charging  lamp 

may  flash  quickly  to  indicate  the 

charging is completed.

  6.  If the charging lamp does not light 

immediately  after  the  charger  is 

plugged in, or if after the standard 

charging time the lamp does not go 

off, consult an authorized dealer.

Note:

    When charging a cool battery 

pack (below 15°C (41°F) in a 

warm place, leave the battery 

pack at the place and wait for 

more than one hour to warm 

up the battery to the level of 

the  ambient  temperature.  

(Battery pack may not be fully 

charged.)

 

  Cool down the charger when 

charging more than two bat-

tery packs consecutively.

 

  Do not insert your fingers into 

contact hole, when holding 

charger or any other occa-

sions.

CAUTION:

   Do not use power source 

from an engine generator.

 

 Do not cover vent holes 

on  the  charger  and  the 

battery pack.

. LAMP INDICATIONS

Flashing

Lit

Flashing quickly

Lit

Flashing

Charger is plugged into a wall outlet. 

Ready to charge.
Now charging

Charging is completed.

Battery pack is warm. Charging will begin

when temperature of battery pack drops.
Charging is not possible. Clogged with 

dust or malfunction of the battery pack.

Flashing slowly

Protective charging

Содержание EY6932 - HAMMER DRILL DRIVER













Отзывы: