background image

- 4 - 

  

8)

  During  charging,  the  charger 

may become slightly warm. This 

is normal. Do not charge the bat-

tery for a long period. 

Symbol 

meaning

V

Volts

Direct Current

n

0

no load speed

…/min

revolutions or

reciprocation per minutes

Forward Rotation

Reverse Rotation

Rotation with Hammering

Rotation only

WARNING;

Some  dust  created  by  power  sand-

ing,  sawing,  grinding,  drilling,  and 

other  construction  activities  con-

tains  chemicals  known  to  the  State 

of  California  to  cause  cancer,  birth 

defects  or  other  reproductive  harm. 

Some examples  of these chemicals 

are:

* Lead from lead-based paints

* Crystalline  silica  from  bricks  and 

cement  and  other  masonry  prod-

ucts

* Arsenic and chromium from chemi-

cally-treated lumber.

To  reduce  your  exposure  to  these 

chemicals:  work  in  a  well  ventilated 

area, and work with approved safety 

equipment, such as dust masks that 

are  specially  designed  to  filter  our 

microscopic particles.

. FOR BATTERY  

CHARGER & 

BATTERY PACK

  1) 

SAVE THESE 

INSTRUCTIONS

  This  manual  contains  important 

safety  and  operating  instructions 

for battery charger EY0230.

  2)  Before using battery charger, read all 

instructions and cautionary markings 

on (1) battery charger, (2) battery 

pack.

  3) 

CAUTION

  To reduce the risk of injury, charge 

only Battery Pack as shown below.

  EY9065, EY9066, EY9080, EY9086,

  EY9180, EY9182, EY9001,

 

EY9006,

  EY9101, EY9106, EY9107,

 

EY9200,

  EY9201, EY9136, EY9230, EY9231

  Other types of batteries may burst 

causing  personal  injury  and  dam-

age. 

  4)  Do not expose charger to rain or 

snow.

  5)  To  reduce  risk  of  damaging  the 

electric plug and cord, pull by plug 

rather than cord when disconnect-

ing charger.

  6)  Make sure cord is located so that it 

will not be stepped on, tripped over, 

or otherwise subjected to damage 

or stress.

Содержание EY6932 - HAMMER DRILL DRIVER













Отзывы: