background image

8

Installation of Water Inlet Hose on Body Side

Connect to the body

1. As illustrated, insert the O-ring side of the 
  water inlet hose straight into the body 
  connection port.
  (If not inserted straight, the O-ring may 
  be damaged.)

2. As illustrated, insert the quick fastener 
  all the way into the connection correctly 
  until a “click” is heard.

Bend

Tighten

Claw end

Hold end

Connection

Insert

Body 

connection 

port

Quick fastener

Bend

Turn gently

Turn to a easily

visible position

and fit the claw.

Make sure to use the water 
inlet hose supplied with the 
product.
(Risk of water leak)

A

3. Tighten the claw securely.
    Bend the hole end downwards.
    Bend the claw end towards the hole end 
    and tighten it. (Until a “click” is heard)

4. With the water inlet hose held in your hands, 
  turn the quick fastener gently. The turning 
  operation should be smooth. (If it is not 
  smooth, it indicates the installation is 
  done improperly.)

Caution:

Serious water leaks may occur if the water inlet hose is installed improperly.

Note

An O-ring must be fitted to the 
front end.
The O-ring must be free of dust.
(Risk of water leak)

Caution

Do not damage (cut or scratch) 
the water inlet hose.
(Risk of water leak)

Caution

When the claw can’t be fit, it 

indicates that the connection isn’t 

inserted all the way in.

Make sure the insert and tighten 

the quick fastener securely.

* If the claw is not tightened securely, 

  the quick fastener will become 

  loosened, resulting in a serious water 

 leak.

Note

About the O-ring

About the 

quick fastener

Example of incorrect connection

O-ring

Water inlet hose

Claw not 

tightened

1

Содержание DL-EH30SE-W













Отзывы: