121
RQT9431
General Issues
Operation
Page
Cannot operate the TV with the
unit’s remote control.
Change the manufacturer code on the remote control.
It may be necessary to set the code on the remote control again after
changing the batteries.
•
•
105
119
Cannot operate the disc.
Press [DRIVE SELECT] to select the DVD drive when operating the disc.
•
26
The remote control doesn’t work.
The remote control code is wrong. Change to the correct code.
The batteries are depleted. Replace them with new ones.
Point the remote control at the remote control sensor on the main unit.
Remove obstacles between the remote control and the main unit.
Remove dust from the transmission window and the unit’s sensor.
Coloured glass may obstruct the signal reception/transmission.
Don’t place the signal sensor in direct sunlight or in areas that may be subject
to sun exposure.
It may be necessary to set the manufacturer code again after changing the batteries.
The HOLD function is activated.
Software is updating when “UPD / ” is displaying on the unit’s display. Wait
until the update is completed.
•
•
•
•
•
•
•
•
•
•
119
7
7
−
−
−
−
105
105
108
The unit is on but cannot be
operated.
Recording drive or playback drive has not been selected properly.
Some operations are prohibited by the disc.
The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (
➔
119, “To restore
the unit if it freezes”).
•
•
•
•
26, 27
−
116
−
“U88” is displayed and the disc
cannot be ejected.
The unit is carrying out the recovery process. The disc may be defective. Do
the following to eject the disc. Try another disc.
(1) Press [
8
] on the main unit to switch to standby mode.
If the unit doesn’t switch to standby mode, reset the unit (
➔
119, “To
restore the unit if it freezes”).
(2) While the unit is turned in standby, press and hold [
g
] and [CH
1
] on the
main unit at the same time for about 5 seconds. (Ejection may take extra
time depending on discs.)
•
−
Cannot eject a disc.
The unit is recording.
The unit may have a problem. Eject the disc as in (2) above.
Linked timer recordings with external equipment is in recording standby (“EXT-
L” on the unit’s display blinks when [
^
] is pressed). Press [EXT LINK] to cancel
the recording standby.
If the HOLD function is activated, above operation does not work. Cancel the
HOLD function.
•
•
•
−
−
62, 105
Startup is slow.
Startup takes time in the following situations:
A disc other than a DVD-RAM is inserted.
The clock is not set.
Immediately after a power failure or the AC mains lead is connected.
When the unit is connected with an HDMI cable.
Set “Power Save” to “Off”in the Setup menu. If connected with an HDAVI
Control 4 compatible TV (VIERA) with the “Standby Power Save” setting
activated on the TV, even with “Power Save” set to “Off” when the TV is in
Standby mode, the unit may take some time to startup.
•
–
–
–
–
•
−
104
General Issues
TV Guide
Page
The TV Guide system does not
receive any data.
Check whether the clock is properly set.
If signal quality is bad (ghost images or limited reception), the TV Guide
system may not be able to receive any data. Check the connection and retune
unit.
•
•
15
96
The empty field is displayed for
some or all stations.
Some stations are not supported by the TV Guide system.
Programme the Timer recording manually.
•
•
−
39
The TV Guide information is not
displayed properly.
There was a programme change or TV Guide information from a broadcast
station was possibly not correctly transmitted.
Check the current programme, e.g. on the Web site for the TV Guide system
provider or station provider.
•
−
The TV Guide data is not updated.
Make sure that the time is set correctly. Set the clock manually.
•
15
Ref
erence
