Panasonic CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU Скачать руководство пользователя страница 93

Страница: 93 / 112

7. Connecting a Home Automation Device

The HA (white) 4P terminal is located on the indoor unit PCB. If a HA device will
be used, connect it to this terminal.

8. Installation Check Sheet

The strength of the installation location is sufficient to support the air
conditioner weight.

The indoor and outdoor units are installed level and vertically.

The power and voltage are as specified.

Inter-unit cables are securely inserted into the terminal block.

Inter-unit cables are securely fixed.

The power cable and inter-unit cables are not connected anywhere along
their paths.

The ground wire is securely connected.

Thermal insulation has been applied to the tubing connections.

Drain connections are secure and water drains properly.

Putty has been used to close the hole in the wall.

Remote controller signals are being positively received.

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

















































































































Результаты поиска

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Отзывы:

Похожие инструкции для CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Бренды по названию

Популярные бренды

Panasonic CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU, Техническое и сервисное руководство

Результаты поиска

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Отзывы:

Похожие инструкции для CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Бренды по названию

Популярные бренды