Panasonic CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU Скачать руководство пользователя страница 28

Страница: 28 / 112

Emergency operation

SENSOR DRY

During DRY operation, the system adjusts the room

temperature and fan speed according to the conditions in the
room, in order to maintain a comfortable room environment.

SENSOR DRY operation

• DRY operation is as shown in the figure below.

PAM- control

• In order to further improve inverter performance, control is

switched between PWM control at low operation speeds, and
PAM control at high operation speeds, making the most
effective use of power.

The compressor operation frequency varies.
The indoor fan operates with 1/f fluctuation.

The compressor operates at a low operating frequency.
The indoor fan operates with 1/f fluctuation.

• Monitoring operation takes place when the room temperature

is below 59°F

(

15°C), or more than 5°F

(

3°C) below the set

temperature.

• When the monitoring range is entered, the compressor stops,

and the indoor fan operates with 1/f fluctuation.

DRY A

DRY B

Monitor

Conditions are monitored at all
times when the room temperature
is below 59°F(15°C).

Load

COOL zone

A zone

B zone

Emergency operation is available when the remote

controller malfunctions, has been lost, or otherwise
cannot be used.

• The set temperature is 4°F(2°C) below the detected room

temperature in the case of cooling operation. The flap and
fan speed settings are AUTO.

(GREEN) (Lamp

Off)

COOL

STOP

To operate the system, press the OPERATION button,

which is also used as the receiver, below the unit display.

Each time this button is pressed, the OPERATION lamp

changes color to indicate the type of operation. Select the
desired type of operation.

7. FUNCTIONS

7-1. Operation Functions

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

















































































































Результаты поиска

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Отзывы:

Похожие инструкции для CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Бренды по названию

Популярные бренды

Panasonic CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU, Техническое и сервисное руководство

Результаты поиска

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Отзывы:

Похожие инструкции для CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Бренды по названию

Популярные бренды