Panasonic CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 112

background image

9

OPERATION WITH THE REMOTE CONTROLLER

1. Operation

2. Adjusting the Fan Speed

A. Automatic fan speed

Simply set the FAN SPEED selector button to the

position.
This automatically sets the best fan speed for the room
temperature.

B. Manual fan speed

If you want to adjust fan speed manually during operation,
just set the FAN SPEED selector button as desired. [

,

, or

]

3. Fan Only

Check that the circuit breaker on the power panel is
turned on.

Press the setting buttons as described below and
change the settings as desired.

STEP 1

Press the MODE selector button
and select the desired mode.
For dehumidifying operation
For cooling operation
For fan only operation

o
o
o

STEP 2

To start the air conditioner, press the ON/
OFF operation button.

STEP 3

Press the TEMP. setting buttons to change
the temperature setting to the desired
temperature.
Adjustable temperature range:

STEP 4

Set the FAN SPEED selector button to the
setting you want.

STEP 5

Press the FLAP button and set the airflow
direction as desired.
(Refer to “ADJUSTING THE AIRFLOW
DIRECTION” on page 12.)

To stop the air conditioner, press the ON/OFF
operation button again.

• Choose the best position in the room for the remote

controller, which also acts as the sensor for room
comfort and transmits the operating instructions.
Once you’ve found this best position, always keep the
remote controller there.

• This appliance has a built-in 5-minute time delay

circuit to ensure reliable operation. When the
operation button is pressed, the compressor will start
running within three minutes. In the event of power
failure, the unit will stop.

STEP 2

STEP 1

STEP 3

STEP 4

STEP 5

NOTE

30 °C max.
16 °C min.

or

86 °F max.
60 °F min.

NOTE

If you want to circulate air without any temperature
control, follow these steps:

STEP 1

Press the MODE selector button to switch to
the fan mode

.

STEP 2

Press the ON/OFF operation button.

STEP 3

Press the FAN SPEED selector button to
select the fan speed of your choice (

,

or

).

STEP 2

STEP 1

STEP 3

«
...
65
66
67
68
69
...
»

Содержание CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

















































































































Отзывы:

Нет отзывов

Похожие инструкции для CS-KS18NB4UW & CZ-18BT1U + CU-KS18NKU

Бренд: ZIBRO CLIMA Страницы: 164

Duct Type Series

Бренд: Samsung Страницы: 40

Бренд: Midea Страницы: 16

ODEUR DE CHINE II

Бренд: Serene House Страницы: 6

DOM413 BL-198DLR

Бренд: Livoo Страницы: 10

Бренд: Salda Страницы: 14

Бренд: Daikin Страницы: 9

Бренд: Walter Roller Страницы: 36

Бренд: Turbo Air Страницы: 33

Бренд: Webasto Страницы: 32

Бренд: Montgomery Ward Страницы: 9

Enviro-Therm SCE-AC5100B230V

Бренд: SCE Страницы: 17

Бренд: ALPATEC Страницы: 8

Бренд: Vaco Страницы: 28

Бренд: Carrier Страницы: 68

Бренд: Danby Страницы: 36

CS/CU-KU12ZKY Series

Бренд: Panasonic Страницы: 32

Бренд: Hitachi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды