59
CQ-VD7001W
Transportation bracket
removal
Be sure to remove the transportation brackets
before use (installation). Use screws (5
mm
ø
x
6 mm) with washers for installation.
Be careful not to lose these screws.
Round Head Screw
(5
mm
ø
x 6 mm)
Round Head Screw
(5
mm
ø
x 6 mm)
Transportation
Bracket
Transportation
Bracket
58
CQ-VD7001W
Installation
Preparation
Dashboard Installation
¡
Before installation, check the radio operation with anten-
na and speakers.
¡
Disconnect the cable from the negative (–) battery termi-
nal (see caution below).
¡
The unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30°.
Installation Opening
The unit can be installed in any dashboard having an open-
ing as shown below. The dashboard should be 4.5 mm - 6
mm thick in order to be able to support the unit.
Installation Precautions
This product should be installed by a professional
installer, if possible.
In case of difficulty, please consult your nearest authorized
Panasonic Service Center.
1. This system is to be used only in a 12 V DC battery sys-
tem (car) with negative ground.
2. Follow the electrical connections carefully (
a
page 64-
69). Failure to do so may result in damage to the unit.
3. Connect the power lead after all other connections are
made.
4. Be sure to connect the battery lead (yellow) to the posi-
tive terminal (+) of the battery or fuse block (BAT) termi-
nal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before connect-
ing it to this unit.
0 – 30°
182 mm
53 mm
Caution
¡
Do not disconnect the battery terminals of a car with
trip or navigational computer since all user settings
stored in memory will be lost. Instead take extra care
with installing the unit to prevent shorts.
Caution
¡
Please follow the laws and regulations of your
province or country for installation of the unit.
¡
When bending the mounting tab of the mounting col-
lar with a screwdriver, be careful not to injure your
hands and fingers.
¡
We strongly recommend you to wear gloves for
installation work to protect yourself from injuries.
❏
Installation Hardware
(For Installation)
❏
Installation Hardware
(For Wiring)
Note:
¡
The number in parenthesis underneath each accessory
part name is the part number for maintenance and serv-
ice.
¡
Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
¡
Use the supplied screws for installation exclusively. In
case of losing any of them, please order the specific
screw.
Qty.
Diagram
Item
No.
Trim Plate
<YEP9FZ2739>
q
1
Mounting Collar
<YEFG012694>
w
1
Mounting Spring
<YEFX0052714>
e
2
Qty.
Diagram
Item
No.
Power Connector
<YAJ024C113A>
!3
1
Reverse Extension Cord
<WAVS05M6000T>
!4
1
Clip Connector
<YEAT034C012>
!5
1
Rear Support Strap
<YEFG04019>
<ZZBISVD7001B>
u
1
Round Head Screw
(5 mmø x 6 mm)
i
2
Flat-Head Screw
(5 mmø x 6 mm)
o
4
Round Head Screw
(4 mmø x 3 mm)
!0
4
<ZZBISVD7001A>
Mounting Bolt (5 mmø)
r
1
Tapping Screw
(5
mm
ø
x 16 mm)
t
1
Hex. Nut (5
mm
ø)
y
1
<ZZBISVD7001E>
Spacer
!1
2
Double-Faced Adhesive Tape
!2
1
set
