38
Setting menus
CABLE LENGTH (SHORT, LONG)
This item sets the compensation for the length of the BNC
cable used for the genlock signals. “SHORT” is set when
the cable is less than 500 meters long; “LONG” is set when
it is 500 meters or longer.
H PHASE (–206 to +49)
This item is used to adjust the horizontal phase during
genlock.
SC PHASE (1, 2, 3, 4, –511 to +511)
This item is used to adjust the color phase during genlock.
CABLE COMP AUTO
When this item is selected and the OK button is pressed,
the cable compensation is adjusted automatically.
Perform these operations to achieve a simple adjustment or
when a waveform monitor, vectorscope or other such
measuring instrument is not available.
CABLE COMP MANUAL (Y: 0 to 255; C: 0 to 255)
Select this item to adjust the cable compensation manually
when C.VIDEO has been selected as the input signal setting
for the SIGNAL SELECT item on the CONTROLLER
SETTING menu.
CABLE COMP MANUAL Y LEVEL (0 to 255)
Select this item to adjust the cable compensation manually
when Y/Pr/Pb has been selected as the input signal setting
for the SIGNAL SELECT item on the CONTROLLER
SETTING menu.
When it is selected, the multi-function controller’s video
output signals are automatically set to Y/Pr/Pb. When it is
released, the original video output signals are restored.
CABLE COMP MANUAL f Response (0 to 255)
Select this item to adjust the compensation for the
frequency response manually when Y/Pr/Pb has been
selected as the input signal setting for the SIGNAL SELECT
item on the CONTROLLER SETTING menu.
When it is selected, the output signals from the camera are
automatically set to Y/C, and the multi-function controller’s
video output signals are set to Y/Pr/Pb. The frequency
response is compensated by adjusting the burst level using
the Pr output signal. When this item is released, the original
video output signals are restored.
CABLE COMP (cable compensation)
menu
G/L SETTING (genlock adjustment)
menu
SIGNAL SELECT
(C.VIDEO
5
C.VIDEO, Y/Pr/Pb
5
C.VIDEO, Y/Pr/Pb
5
Y/Pr/Pb)
This is used to set the multi-function controller’s input
signals and output signals.
When the signals supplied to the multi-function controller
have been set to C.VIDEO (composite signals), the output
signals signals are fixed to the C.VIDEO as well.
When the signals supplied to the multi-function controller
have been set to Y/Pr/Pb (component signals), either the
Y/Pr/Pb or C.VIDEO signals can be selected as the output
signals.
BUZZER SET (ON/OFF)
This is used to set the buzzer contained inside the control
panel to ON or OFF. The buzzer does not sound when OFF
is selected as this item’s setting.
At the ON setting, the buzzer sounds when the CALL button
is pressed and when a tracing memory operation (entry,
recall or change) has been started, suspended or data entry
has been completed.
EXT CONTROL OUT (ON/OFF)
When ON is selected as this item’s setting, the pan-tilt head
system’s control signals are output from the EXTERNAL
CONTROL OUT connector used for additional functions.
Since it is not supported at the present time, select the OFF
setting for use.
COMPONENT (RGB, Y/Pr/Pb, Y/C)
This item is used to select the video signals which are to be
output when the RGB card (AW-PB302) has been installed
in the OPTION CARD slot.
MEMORY LENGTH (30s, 60s, 150s, 300s)
This item is used to set the tracing memory entry time
(memory length) and number of memories.
30s : 30 seconds
a
10 memories
60s : 60 seconds
a
5 memories
150s : 150 seconds
a
2 memories
300s : 300 seconds
a
1 memory
<Note>
If data has already been entered into a tracing memory, the
entry time and number of memories cannot be set. Before
entering different settings, delete the contents of the tracing
memory.
HEAD SW (R) FUNCTION (ON/OFF)
When ON is selected as this item’s setting, it is no longer
possible to switch the adjustment dial functions (IRIS and
FOCUS) using the button on the top surface of the
PAN/TILT lever.
Since it is not supported at the present time, select the OFF
setting for use.
VIRTUAL STUDIO MODE (ON/OFF)
When ON is selected as this item’s setting, the camera’s
video signals are switched to the corrected color position for
using the blue background of the virtual studio.
CONTROLLER SETTING (controller
setting) menu
Содержание AWRP605P - MULTI FUNCTION CONTROLLER
Страница 45: ......
