Panasonic AWRP605P - MULTI FUNCTION CONTROLLER, Руководство по эксплуатации

Страница: 22 / 46

22
Operation
$ Video signal cable compensation
Signal deterioration caused by the length of the cables from
the pan-tilt head to the main unit is compensated for.
When the length of the cables from the pan-tilt head to the
main unit exceeds 500 meters, set the cable compensation
switch inside the pan-tilt head to ON.
For further details, refer to the operating instructions of the
pan-tilt head.
1. Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the MENU button, turn the menu setting control
(main), and set it so that the CABLE COMP item
appears at the top of the LCD panel.
3. Press the OK button.
The following item appears on the LCD panel.
4. Press the OK button.
The adjustment of the cable compensation for the
currently selected pan-tilt head system commences, and
the OK button’s lamp flashes.
If composite signals have been set as the video input
signals, the output signals from the convertible camera
are switched to color bar signals, and automatic
adjustment is performed.
Alternatively, if component signals have been set as the
video input signals, the output signals from the
convertible camera are switched to color bar signals of
Y/C signals, and automatic adjustment is performed.
5. Upon completion of the adjustment, the OK button’s
lamp goes off. The following item appears on the LCD
panel.
6. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue adjusting the cable compensation for each
system concerned.
<Note>
A small error may arise in the automatic adjustment. If
precise adjustment is required, perform the adjustment
manually. (Refer to the following page.)
C CA AB BL LE E C CO OM MP P A AU UT TO O
A AD DJ JU US ST T O OK K
C CA AB BL LE E C CO OM MP P A AU UT TO O
A AU UT TO O A AD DJ JU US ST T
C CA AB BL LE E C CO OM MP P A AU UT TO O
S ST TA AR RT T? ?
n
O OK K K Ke ey y
C CA AB BL LE E C CO OM MP P
n
O OK K K Ke ey y
Automatically adjusting the cable compensation
CONTROL/PREVIEW MONITOR OUT SEL
AUX 1 2 3 4 5
TALLY
TRACING MEMORY
LAMP
MENU
LIMIT
OFF
LIMIT
ON
FULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT
R/B
GAIN/PED
WHITE
BAL
AWC
GAIN
MODE
CLOSE WIDE NEAR
DATA SET
TR/PSET M.LOCK
MEMORY
IRIS
IRIS
IRIS
OPEN
ZOOM
TELE
FOCUS
FAR
CALL
INCOM
LEVEL
FOCUS
OPEN
FAR
TELE
OFF
ON
OPERATE
WIDE
ZOOM/FOCUS/IRIS
ABC
ATW
A
B
NG
OK
START/STOP RESTORE RESET
DEF WIP H/F EXT ND OPTION
PAN/TILT SET CAMERA CONTROL
TRACING/PRESET MEMORY
IRIS
SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 130
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
DOWN
PA N / T I LT / F O C U S / I R I S
U P
L R
CLOSE
NEAR
OPEN
FAR CLOSE
NEAR
2
2 3•4
1
If the automatic adjustment was not performed properly,
the following item appears on the LCD panel.
Check the connection of the output signals from the
convertible camera and cables, and proceed with the
automatic adjustment again.
If the automatic adjustment was not performed properly
again even by following the automatic adjustment
procedure, perform the adjustment manually instead.
Consult your dealer if the adjustment still cannot be
performed properly even when the manual procedure is
followed.
C CA AB BL LE E C CO OM MP P A AU UT TO O
A AD DJ JU US ST T N NG G