Panasonic AWRP605 - CCU & PAN/TILT CONTR, Руководство по эксплуатации

Страница: 33 / 92

33
1. Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the button in which the tracing memory data to be
recalled has been entered.
The pan-tilt head system is set to the start position
entered in the tracing memory.
3. After the pan-tilt head system has been set to the tracing
memory start position status and then stopped, press the
button in which the tracing memory data has been
entered again .
The pan-tilt head system now starts the operations
entered in the tracing memory.
<Notes>
O
When the AW-PH350 is used as the pan-tilt head, no
operations will be acknowledged even if the button in
which the tracing memory data has been entered is
pressed before the head is set to the start position
status.
If, when a model other than the AW-PH350 is used as
the pan-tilt head, the button in which the tracing
memory data has been entered is pressed before the
head is set to the start position status, the operations
of the series of settings stored in the memory will be
performed again from the position where the button
was pressed.
Therefore, the button in which the tracing memory
data has been entered must be pressed after the pan-
tilt head system has been set to the tracing memory
start position status and stopped.
O
Press the START/STOP button to suspend the recall
of the data from tracing memory at any time.
This recall can also be suspended as soon as the
pan, tilt, zoom or focus operation has been initiated.
O
The buzzer sounds when tracing memory data recall
is started or suspended and when the data recall is
completed.
Recalling tracing memory data
1. Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the button in which the tracing memory data to be
changed has been entered, and call the start position of
the tracing memory.
3. Press the RESTORE button.
The RESTORE button’s lamp flashes, and the start
position setting of the tracing memory can be changed.
<Note>
The change mode is canceled if the START/STOP
button is pressed at this point.
4. Press the RESTORE button again.
The pan-tilt head system starts performing the
operations entered in the tracing memory, and the
RESTORE button’s lamp stops flashing and comes on.
As with the data entry process, buttons No. 11 through
No. 30 serve as a general guideline for the time.
5. The tracing memory operations are changed.
<Note>
Partial changes cannot be made to tracing memory
operations. Enter all the operations again starting from
the point where the change is made.
6. As soon as the lamp in button No. 11 goes off, the
buzzer sounds, and the tracing memory change is
completed.
Making changes to the tracing memory
Operation
CONTROL/PREVIEW MONITOR OUT SEL
AUX 1 2 3 4 5
TALLY
TRACING MEMORY
LAMP
MENU
LIMIT
OFF
LIMIT
ON
FULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT
R/B
GAIN/PED
WHITE
BAL
AWC
GAIN
MODE
CLOSE WIDE NEAR
DATA SET
TR/PSET M.LOCK
MEMORY
IRIS
IRIS
IRIS
OPEN
ZOOM
TELE
FOCUS
FAR
CALL
INCOM
LEVEL
FOCUS
OPEN
FAR
TELE
OFF
ON
OPERATE
WIDE
ZOOM/FOCUS/IRIS
ABC
ATW
A
B
NG
OK
START/STOP RESTORE RESET
DEF WIP H/F EXT ND OPTION
PAN/TILT SET
CAMERA CONTROL
TRACING/PRESET MEMORY
IRIS
SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 130
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
DOWN
PA N / T I LT / F O C U S / I R I S
U P
L R
CLOSE
NEAR
OPEN
FAR CLOSE
NEAR
START/STOP
1 2
CONTROL/PREVIEW MONITOR OUT SEL
AUX 1 2 3 4 5
TALLY
TRACING MEMORY
LAMP
MENU
LIMIT
OFF
LIMIT
ON
FULL EMPTY
OK
LCD
CONTRAST
CAMERA
CONTROL
START
POINT
R/B
GAIN/PED
WHITE
BAL
AWC
GAIN
MODE
CLOSE WIDE NEAR
DATA SET
TR/PSET M.LOCK
MEMORY
IRIS
IRIS
IRIS
OPEN
ZOOM
TELE
FOCUS
FAR
CALL
INCOM
LEVEL
FOCUS
OPEN
FAR
TELE
OFF
ON
OPERATE
WIDE
ZOOM/FOCUS/IRIS
ABC
ATW
A
B
NG
OK
START/STOP RESTORE RESET
DEF WIP H/F EXT ND OPTION
PAN/TILT SET
CAMERA CONTROL
TRACING/PRESET MEMORY
IRIS
SPEED
PRIORITY
FOCUS
BAR
CAM
TR
PSET
LOW
HIGH
AUTO
MANU
AUTO
MANU
LOCK
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 130
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
DOWN
PA N / T I LT / F O C U S / I R I S
U P
L R
CLOSE
NEAR
OPEN
FAR CLOSE
NEAR
1 2
3•4