Operating Instructions
Service switch settings
SW1 to SW3 (camera address setting switches)
Configure the camera address.
Set this to AUTO under normal circumstances. When cameras are set
to AUTO, addresses will be assigned to the cameras automatically
in response operation from the controller in the order in which the
cameras were connected.
To manually configure the address, set the switches as follows.
Address
AUTO
1
2
3
4
5
6
7
SW1
OFF
ON
OFF ON
OFF ON
OFF ON
SW2
OFF
ON
ON
OFF OFF ON
ON
OFF
SW3
OFF
ON
ON
ON
ON
OFF OFF OFF
SW4 (communication format selection switch)
Selects the communication format.
When this is set to ON, standard serial communication is enabled.
When this is set to OFF, Panasonic's proprietary serial
communication is enabled.
SW5 (maintenance switch)
Fixed at OFF.
Do not change this switch setting.
SW6 (infrared output switch)
When this is set to ON, infrared output is enabled. The signal received
via the remote control sensor is output from pins 7 and 8 of the <RS-
232C IN> connector.
Signal output is disabled when this is set to OFF.
SW7 (communication baud rate switch)
When this is set to ON, the baud rate is 38400 bps.
When this is set to OFF, the baud rate is 9600 bps.
SW8 (communication connector switch)
When this is set to ON, the RS-232C is enabled.
When this is set to OFF, the RS-422 is enabled.
Simultaneous output conditions for each video
format
z
SDI/HDMI/VIDEO output
Format
SDI
output
HDMI
output
VIDEO
output
*
4
HD/SDI
1080/59.94p
1080/50p
1080/59.94i
1080/50i
1080/29.97PsF
*
1
1080/25PsF
*
2
1080/23.98PsF
1080/29.97p
*
3
1080/25p
*
3
1080/23.98p
*
1
720/59.94p
720/50p
SD/SDI
480/59.94p
576/50p
480/59.94i
576/50i
*
1
OVER 59.94i output (your monitor may recognize the signal as
59.94i).
*
2
OVER 50i output (your monitor may recognize the signal as 50i).
*
3
Native output
*
4
480/59.94i and 576/50i is output to the VIDEO output regardless of
the format setting.
z
IP video transmission output (1-/multi-channel display)
1-channel display
Resolution
1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90
(non-dependent on SYS format)
Frame
rate
59.94Hz
1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/
60 fps
*
1
50Hz
1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps
*
2
*
1
60 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
*
2
50 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
Multi-channel display
Setting
H.264 CH1 H.264 CH2
H.264
CH3/CH4
JPEG
CH1/CH2/
CH3
*
3
Resolution
1920×1080
1280×720
1920×1080
1280×720
640×360
320×180
160×90
1280×720
640×360
320×180
160×90
1920×1080
1280×720
640×360
320×180
160×90
Frame
rate
59.94Hz
60fps
5 fps
15 fps
30 fps
5 fps
15 fps
30 fps
1 fps
2 fps
3 fps
5 fps
6 fps
10 fps
15 fps
30 fps
50Hz
50 fps
5 fps
12.5 fps
25 fps
5 fps
12.5 fps
25 fps
1 fps
2 fps
5 fps
10 fps
12.5 fps
25 fps
*
3
Different resolutions must be specified for JPEG CH1 / CH2 / CH3.
38
Parts and their functions (continued)
