Panasonic AKW8115 Скачать руководство пользователя

Страница: 52 / 61

KW8M Eco-POWER METER (1A/5ACT input type)

Data item

(MEWTOCOL)

Name

Unit

Kind of date

Range: Hexadecimal

(Range: Decimal)

MODBUS

Function

code

0096H<LSB>
(DT00150)
0097H<MSB>
(DT00151)

Load ON-time

0.1h

Unsigned 32bit

0H to F423FH (0 to 999999)

03H/

06H/10H

0098H<LSB>
(DT00152)
0099H<MSB>
(DT00153)

Load OFF-time

0.1h

Unsigned 32bit

0H to F423FH (0 to 999999)

03H/

06H/10H

009AH<LSB>
(DT00154)
009BH<MSB>
(DT00155)

Pulse count value

－

Unsigned 32bit

0H to 5F5E0FFH (0 to 99999999)

03H/

06H/10H

009EH<LSB>
(DT00158)
009FH<MSB>
(DT00159)

Preset value

－

Unsigned 32bit

0H to 5F5E0FFH (0 to 99999999)

03H/

06H/10H

00A0H<LSB>
(DT00160)
00A1H<MSB>
(DT00161)

Prescale value

－

Unsigned 32bit

0H to 186A0H (0 to 100000)

03H/

06H/10H

00A2H
(DT00162)

Max.
counting speed

Unsigned 16bit

1EH (30), 7D0H (2000)

03H/

06H/10H

00A3H
(DT00163)

Auto-off time

min

Unsigned 16bit

0H to 63H (0 to 99)

03H/

06H/10H

00AAH<LSB>
(DT00170)
00ABH<MSB>
(DT00171)

Voltage L1V (R)

0.1V

Unsigned 32bit

0H to 1869FH (0 to 99999)

03H

00ACH<LSB>
(DT00172)
00ADH<MSB>
(DT00173)

Voltage L2 (S/T)

0.1V

Unsigned 32bit

0H to 1869FH (0 to 99999)

03H

00AEH<LSB>
(DT00174)
00AFH<MSB>
(DT00175)

Voltage L3V (S/T)

0.1V

Unsigned 32bit

0H to 1869FH (0 to 99999)

03H

00B0H<LSB>
(DT00176)
00B1H<MSB>
(DT00177)

Instantaneous
active power

0.01kW

Unsigned 32bit

0H to 5F5E0FFH (0 to 99999999)

03H

00B2H<LSB>
(DT00178)
00B3H<MSB>
(DT00179)

Instantaneous
reactive power

0.01kvar

Signed 32bit

FF676981H to 5F5E0FFH
(-9999999 to 99999999)

03H

00B4H<LSB>
(DT00180)
00B5H<MSB>
(DT00181)

Instantaneous
apparent power

0.01kVA Unsigned 32bit

0H to 5F5E0FFH (0 to 99999999)

03H

<LSB>: Least significant byte
<MSB>: Most significant byte

note 1) 03H: Read 06H/10H: Write

2) Data register except specified is “0”.
3) If each setting value is wrote by communication, it memories to internal EEP-ROM at the same

time. Therefore, change setting frequently makes EEP-ROM’s life short. Avoid to usage like this.

4) Write a data within the range when you write it.

Содержание AKW8115






























































Результаты поиска

Содержание AKW8115

Отзывы:

Похожие инструкции для AKW8115

Бренды по названию

Популярные бренды

Panasonic AKW8115, Руководство пользователя

Результаты поиска

Содержание AKW8115

Отзывы:

Похожие инструкции для AKW8115

Бренды по названию

Популярные бренды