Panasonic AJ-HDR150P, Руководство по эксплуатации

Страница: 23 / 42

23
Display Panel
Parameter List
USER SET
Setting item Setting Remarks
Dropped Frame DF
NDF Selects the frame mode in use.
Protocol Odetics
Louth Selects the control protocol in use with
RS-422A.
FF.REW Max x32, x64,
x128 Selects the speed for FF/REW.
SDTI Slow Audio Valid
Invalid Selects audio data output for playback
at
a
1 speed or below.
Rec Start
Position 00:00:00
00:59:59
01:00:00 Selects the recording starting point
when recording instruction has been
given by operating the front panel
when creating a new CLIP.
Record Duration 10min
15min
30min
45min
1H
2H
4H
8H Selects the recording time length of
CLIP ID used during loop recording (L-
REC).
<Note>
O
Upon writing over the existing CLIP
ID, loop recording takes place within
the length of recording time set from
the current position.
O
Loop recording operation takes
place only during STOP.
FTP Put Offset 00:00:00
00:59:59
01:00:00 Selects the recording starting point
when recording is done through
transmission from a non-linear system.
SDTI Illegal Input Rec Stop
Continue Selects operation when SDTI signal
has detected no signal during
recording.
Ch1 Default Rate 25Mbps
50Mbps
100Mbps Selects the format of signals used in
each channel.
However, the upper limit of maximum
usable stream count (25 Mbps mode
taken as 1) that has been set cannot
be exceeded.
For details, consult your dealer.
Ch2 Default Rate 25Mbps
50Mbps
100Mbps
Ch3 Default Rate 25Mbps
50Mbps
100Mbps
Ch4 Default Rate 25Mbps
50Mbps
100Mbps
Ch1 Default
Times x1, x2, x4
Ch2 Default
Times x1, x2, x4
Ch3 Default
Times x1, x2, x4
Ch4 Default
Times x1, x2, x4
A/S SET
Setting item Setting Remarks
CH1 CF Enable On
Off Selects channel 1 color frame control.
CH1 VOUT
SetUp Add
Thru Selects setup level during channel 1
playback.
CH1 VIN SetUp Cut
Thru Selects setup level during channel 1
recording.
CH1 SYS H –121
0
+120
Performs rough tuning of channel 1
system phase in relation to standard
signal. (37ns step)
CH1 SYS SC 0 1023 Performs fine tuning of channel 1
system phase in relation to standard
signal. (0.35° step)
CH1 SCH –128
0
+127
Performs tuning of channel 1 SC-H
(Subcarrier to Horizontal) phase.
(1.41° step)
CH2 CF Enable On
Off
Channel 2 setting is the same as for
channel 1.
CH2 VOUT
SetUp Add
Thru
CH2 VIN SetUp Cut
Thru
CH2 SYSH –121 0
+120
CH2 SYS SC
0 1023
CH2 SCH
–128 0
+127
CH3 CF Enable On
Off
Channel 3 setting is the same as for
channel 1.
CH3 VOUT
SetUp Add
Thru
CH3 VIN SetUp Cut
Thru
CH3 SYSH –121 0
+120
CH3 SYS SC 0 1023
CH3 SCH
–128 0
+127
CH4 CF Enable On
Off
Channel 4 setting is the same as for
channel 1.
CH4 VOUT
SetUp Add
Thru
CH4 VIN SetUp Cut
Thru
CH4 SYSH –121 0
+120
CH4 SYS SC 0 1023
CH4 SCH –128 0
+127
indicates factory setting mode.