Panasonic AJ-HD3700H Скачать руководство пользователя

Страница: 75 / 204

– 75 –

TC/CHR menu

Table of user bit settings

F1 (SOURCE)

INT (internal) TC

S LTC
S VITC

EXT LTC

F2 (TC SLAVE)

——

SLAVE

DIRECT

F3 (UB SLAVE)

OFF

F10 (TCR)

LTC

AUTO

VITC

LTC

AUTO

VITC

LTC

AUTO

VITC

LTC

AUTO

VITC

LTC

AUTO

VITC

LTC

AUDIO

VITC

LUBG mode

REGEN

INT UB

PRESET

INT UB

EXT REGEN

INT UB

PRESET

INT UB

DIRECT

VUBG mode

INT UB

REGEN

INT UB

PRESET

INT UB

EXT REGEN

INT UB

PRESET

INT UB

EXT REGEN

INT UB

PRESET

The user bit can be set in all modes except for recording.

DIRECT:

The external LTC input signal is recorded directly and output.
It is not synchronized with the internal reference signal.

REGEN:

The user bit is slave-locked to the value read out on the tape.
The user bit cannot be set.

EXT REGEN:

The user bit is slave-locked to the externally input VITC or LTC.
The user bit cannot be set.

PRESET:

The user bit is not locked to the value read out on the tape or external input.
The user bit can be set.

INT UB:

In this mode, the previous user bit is retained, and neither the REGEN nor PRESET functions
can be implemented.
To set the user bit again, use the F1 (SOURCE), F2 (TC SLAVE) or F3 (UB SLAVE) key to
select one of the three modes above.

Содержание AJ-HD3700H













































































































































































































Результаты поиска

Содержание AJ-HD3700H

Отзывы:

Похожие инструкции для AJ-HD3700H

Бренды по названию

Популярные бренды

Panasonic AJ-HD3700H, Руководство по эксплуатации

Результаты поиска

Содержание AJ-HD3700H

Отзывы:

Похожие инструкции для AJ-HD3700H

Бренды по названию

Популярные бренды