Panasonic AJ-HD3700H Скачать руководство пользователя

Страница: 39 / 204

– 39 –

VIDEO OUT SET UP LINE BLK (video output line blanking) menu

∑

Setting the line blanking

The blanking lines in the vertical blanking period can be set in 1-line increments.

(1) Press the center cursor key.

The cursor now appears.

(2) Move the cursor and select the lines to be blanked.

(3) Press the center cursor key to select ON or OFF for the display.

ON:

The lines are blanked.

OFF:

The non-blanking status is established, and no lines are selected.

(4) Press the ENT key.

The blanking is now entered.

(5) To return to the previous screen, press the F8 (EXIT) key.

Center cursor key

Cursor key

OFF

Содержание AJ-HD3700H













































































































































































































Результаты поиска

Содержание AJ-HD3700H

Отзывы:

Похожие инструкции для AJ-HD3700H

Бренды по названию

Популярные бренды

Panasonic AJ-HD3700H, Руководство по эксплуатации

Результаты поиска

Содержание AJ-HD3700H

Отзывы:

Похожие инструкции для AJ-HD3700H

Бренды по названию

Популярные бренды