Panasonic AJ-HD3700H Скачать руководство пользователя | Manualshive

Страница: 164 / 204

background image

– 164 –

DIAG menu error messages

A warning mark (W) blinks at the top left of the screen when an er-
roneous setting, failure to verify a condition, warning or other
problem that interferes with the use of the VTR has arisen.

If the DIAG key is pressed while a warning is shown, an error message appears on the screen.

There are the following three kinds of DIAG menu screens.

This is the menu that appears initially when the DIAG key is pressed.
An error message corresponding to the unmasked (not canceled) warning which
has just occurred is displayed.

This is the menu that appears when the F2 (MENU MASKED) key is pressed.
An error message corresponding to the masked (canceled) warning is displayed.

This is the menu that appears when the F3 (MENU LAST) key is pressed.
The error messages for the last three warnings are displayed.

°

Any error message is cleared as soon as the error is remedied.

DIAG LAST menu

DIAG MASKED menu

DIAG ACTIVE menu

F13

F12

F11

F10

F9

F8

F7

F6

F5

F4

F3

F2

F1

«
...
162
163
164
165
166
...
»

Содержание AJ-HD3700H













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AJ-HD3700H

Бренд: GE Страницы: 32

Бренд: JVC Страницы: 16

Бренд: JVC Страницы: 68

Бренд: JVC Страницы: 72

Бренд: JVC Страницы: 4

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Sylvania Страницы: 94

VR2135 and warranty

Бренд: Zenith Страницы: 40

Бренд: Panasonic Страницы: 142

OmniVision PV-C1324-K

Бренд: Panasonic Страницы: 148

Бренд: Philips Страницы: 2

Бренд: Panasonic Страницы: 40

Бренд: JVC Страницы: 16

Бренд: RCA Страницы: 56

Бренд: RCA Страницы: 64

Бренд: RCA Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды