Panasonic AFP7CPS Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 79

background image

General-Purpose Communication



Timing chart



Data in the table [S] specified by GPSEND instruction are sent, in ascending order from

lower bytes.



During the sending process, the "General-purpose communication Sending active flag" (Y8)

turns ON. The flag is turned OFF when sending is completed. (The flag does not turn off
right after the execution of the instruction. It turns off at the beginning of the second scan.)



The sending result (0: normal completion, 1: abnormal completion) is saved in the general-

purpose communication sending result flag (Y0).

Confirm OFF

Conditions to enable execution of
GPSEND instruction
Clear to send flag (X8): ON
Sending active flag (Y8): OFF

Sending done result flag (Y0):
Normal completion: OFF
Abnormal completion: ON

Execute GPSEND

General-purpose

communication Sending

active flag (Y8)

Sending done result

flag (Y0)

Sending data

General purpose

communication Clear to

send flag (X8)

Confirm ON

Sending active flag (Y8):
Sending data: ON, Sending done: OFF



I/O allocation

COM port no.

Name

Explanation

X8

General-purpose
communication Clear to
send flag

Turns ON when the unit is set to the general-purpose
communication mode.

Y8

General-purpose
communication
Sending active flag

Turns ON during sending data based on general-purpose
communication GPSEND.
Turns OFF when the sending process is completed.

Y0

Sending done result
flag

Reports completion result of sending data in genera-purpose
communication or master communication.
(Normal completion: 0, Abnormal completion: 1)

(Note 1) Each contact is used for reading the operation status. Do not write over it with a user program.

(Note 2) When the sending time is shorter than the scan time, the "General-purpose communication Sending active

flag" (Y8) turns OFF when the GPSEND instruction is executed in the subsequent scan following data
sending completion. In all cases, it is turned ON for at least one scan time.

KEY POINTS



Specify the port targeted for communication, using UNITSEL instruction
immediately before GPSEND instruction.



Maintain the ON conditions for GPSEND instruction until sending is
completed and the general-purpose communication sending active flag (Y8)
turns OFF.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
...
52
53
54
55
56
...
»

Содержание AFP7CPS Series
















































































Отзывы:

Нет отзывов

Похожие инструкции для AFP7CPS Series

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Saitek Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: UE Страницы: 4

Бренд: XBOX Страницы: 2

Бренд: D-Link Страницы: 40

Бренд: Yardney Страницы: 8

Бренд: HABONIM Страницы: 9

Бренд: Saga Страницы: 9

Бренд: Mamas & Papas Страницы: 44

Бренд: Mamas & Papas Страницы: 8

Бренд: Omegalink Страницы: 2

Бренд: MamaLove Страницы: 9

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренд: u-blox Страницы: 28

Бренд: u-blox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды