Panasonic A35US Скачать руководство пользователя | Manualshive

Страница: 11 / 29

background image

Operation manual for Narrow-pitch connectors A35US

Panasonic Corporation
industrial.panasonic.com/ac/e/

©

Panasonic Corporation 2015

ACCTF14E-3 201509

- 10 -

(2)

FPC board specifications

Control the thicknesses of the coverlay and adhesive to prevent poor
soldering.
This connector has no stand-off.
Therefore, minimize the thickness of the coverlay, etc. so as to prevent the
occurrence of poor soldering.

If poor soldering occurs frequently, check the actual thickness of each insulation
layer. Generally, the coverlay thickness is set to about 30

μ

m, including the

adhesive. If the thickness exceeds 30

μ

m, design the board so as to remove the

coverlay under the connector.

(3)This connector is often used for connecting the motherboard and FPC board. In

this case, if the FPC board is too short, a load that causes deviation will be applied
to the connector.
Make sure to create a design that provides some allowance in the FPC board.

Connector
terminal

Solder

Molded part of the connector

Coverlay (polyimide)

Adhesive (epoxy adhesive recommended)

Adhesive (epoxy adhesive recommended)

Copper foil

Base material (polyimide)

Reinforcing plate + Adhesive
(epoxy adhesive recommended)

NG: Too long

Fixed

Connector

NG: Too short

Positional deviation

Motherboard

Part where FPC board

is fixed

«
...
9
10
11
12
13
...
»

Содержание A35US






























Отзывы:

Нет отзывов

Похожие инструкции для A35US

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: ABB Страницы: 6

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: Bacharach Страницы: 48

Бренд: HABYS Страницы: 16

Бренд: A&D Страницы: 29

Бренд: Kärcher Страницы: 148

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

Бренд: Unitech Страницы: 37

Sedeo Lite Q700M

Бренд: Quickie Страницы: 9

Бренд: Global Страницы: 13

Бренд: HOMCOM Страницы: 11

Powerator 1800 compact

Бренд: Seto Страницы: 39

Бренд: Veeder-Root Страницы: 58

Fault Trapper TFT100

Бренд: Platinum Tools Страницы: 8

Бренд: Vari Lite Страницы: 14

Бренд: Qdot Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды