background image

 

 
 

 

 
 
 
 
 
Before you begin ensure that the gas hose connector and electrical cord are plugged in correctly. 

 
START UP 

 

 

Press the ON/OFF Button once to start the heater and the operation light (green)  
will light up.  

 

After a short delay the combustion light (red) will light up. this indicates proper 
ignition has been achieved and the burner is on. 

 

If the heater fails to light, repeat the procedure after first pressing the ON/OFF button 
to turn the unit off. 

 
 
 

Note: 

 

When using the heater for the first time or after long periods of disuse, ignition may not 
occur the first time it is operated as there may be air within the pipes. 

 

The unit may make noises after igniting or extinguishing the heater. This is due to expansion and 
contraction of the heater components and is normal. 

 
ROOM TEMPERTATURE ADJUSTMENT 

 

 

The set temperature can be raised or lowered by using the  
temperature selection buttons. 

 

Press any temperature selection button to show the  
current room temperature. The actual room  
temperature is shown by the “flashing” green light. 

 

Press the appropriate lower or higher temperature 
selection button to set your desired temperature.  

 

Note: 

 

Your room may not arrive at the “SET” temperature due to the size of  
room, construction of room, location of the heater or external  
temperatures. 

 

For the heater to ignite the “SET” temperature must be higher 
than the “‘ROOM” temperature. 

 
TURNING HEATER OFF 

 

Press the ON/OFF button once. All lights will go out. 
 

Note: 

 

The heater fan will continue to operate for several minutes. 
This is to lower the temperatures inside the heater and is normal. 

 

Please do not turn the power supply off during this period. 

 
ADJUSTMENT OF HOT AIR OUTLET 

 

The direction of heated air can be adjusted by moving  
the louvre plate up or down as required.  
 

Caution!  

Adjust louvre plate only when heater has cooled.  
 

 

 

 

 

Operating Instructions 

 

Содержание PJC-S13F

















Отзывы: