manualshive.com logo in svg

Paloma PH-203EWH, Руководство пользователя и инструкции по установке

Поделиться
Скачать
Paloma PH-203EWH Скачать руководство пользователя страница 46

46

 

 

INSTALLATION – CONTROLLERS

 

 

Wiring installation:

 

 

1. 

Penetrate the wall with a 30-35 mm hole at the controller location.

 

 

2. 

Install the supplied cable between the location of the controller and the water heater.

 

 

3. 

Remove the base plate from the controller.

 

 

4. 

Peel off one side of the adhesive paper from the foam packing and adhere to the back face of the base 
plate. This is the side without the projections.

 

 

5. 

Peel off the remaining adhesive paper from the foam packing.

 

6. 

Draw the cable through the central hole in the base plate.

 

 

7. 

Fix the base plate to the wall using suitable screws and wall anchors. 

Ensure the projections in the base plate are pointing upwards.

 

8. 

Plug the controller wire into the Bathroom controller cable.

 

 

9. 

Place the controller over the base plate. 

 

Ensure the projections in the base plate fit into the housings in the controller. 

10. 

Fix the controller to the base plate at the bottom of the controller, using the screw provided. 

 

11. 

Proceed to “Connecting the Controller(s) to the Water Heater” on page 47. 

 
 

 

 

Bathroom Deluxe Controller Installation

 

Содержание PH-203EWH

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды