Paloma PH-203EWH Скачать руководство пользователя страница 30

30

 

 

SAVE A SERVICE CALL

 

 

CLOUDS OF WHITE ‘VAPOUR’ FROM THE FLUE TERMINAL

 

During  the  heating  cycle, it  is  not  unusual  t

o  see  water  vapour  clouds 

steaming from the flue terminal, particularly on cold days. This is normal 
operation of the water heater. 

 

PRESSURE RELIEF VALVE DISCHARGING 

A  pressure  relief  valve  is  incorporated  into  the  water  heater  controls. 
This valve protects the water heater, by allowing water to escape, in the 
event of excessive pressure build up in the waterways. 

 

Normal operation 

A small volume of water may discharge from the bottom of the water 
heater when a hot tap is suddenly closed. 

 

Continuous dribble 

A  continuous  dribble  may  indicate  the  water  supply  pressure  is 
above  the  design  pressure  for  the  water  heater.  If  so,  a  pressure 
limiting valve must be installed on the cold water supply pipe to the 
water heater. 

 

ERROR CODE 

The water heater provides  a diagnostic error code in the event of an interruption to its operation. The error 
code is displayed on the controller(s) (if installed) as a numerical value and on the OK MONITOR on the front 
of the water heater as a series of flashes. If an error code appears: 

 

Close the hot tap, turn off the controller(s) and switch off the 
electrical supply to the water heater. 

 

Check the gas isolation valve at the gas inlet to the water heater is 
fully open. 

 

Wait 5 minutes, then switch on the electrical supply to the water 
heater, turn on a controller and open a hot tap. 

If  the  error  code  persists,  take  note  of  the  numerical  code  if  a 
controller(s) is installed and the number of flashes on the OK MONITOR, 
turn  off  the  hot  tap  and  turn  off  the  controller(s).  Phone  your  nearest 
Paloma Service centre to arrange for inspection. 

 

HIGH GAS BILLS 

Should you at any time, feel your gas account is too high, we suggest 
you check the following points: 

 

Is one outlet (especially the shower) using more hot water than 
you think? 

Carefully  review  the  family’s  hot  water  usage.  Inexpensive  flow 
control  valves can  be  easily fitted to the shower  outlets to reduce 
water usage. 

 

Is the gas booster water heater operating too frequently? 

Refer to “Gas Booster Operating Too Frequently” on page 29. 

 

Consider recent changes to your hot water usage pattern and check 
if there has been any increase in tariffs since your previous accoun

t.

 

 

IF YOU HAVE CHECKED ALL THE FOREGOING AND STILL BELIEVE YOU NEED ASSISTANCE, CALL 
YOUR NEAREST PALOMA SERVICE CENTRE.

 

Содержание PH-203EWH

























































Отзывы: