PaloAlto Networks PA-7050 PAN-AIRDUCT Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 70

background image

Switch Management Card (SMC)

16

• PA-7050 Modules and Interface Card Overview

Palo Alto Networks

Interpreting the SMC LEDs

Figure 6 shows the LED dashboard that is located on the Switch Management Card (SMC). Table 4
describes the LED functions and states of the LED dashboard, Table 5 describes the SMC SFP and Port
LEDs, Table 6 describes the SMC HA port LEDs, and Table 7 describes the HSCI ports.

Figure 6. SMC LEDs

Table 4. Functions and States of the SMC LED Dashboard

LED

State

Description

PWR
(POWER)

Green

The device is powered.

Off

Power is off.

STS
(STATUS)

Green

Device is operating normally.

Yellow

Device is booting up.

HA

Green

Device is the current active device.

Yellow

Device is the current passive device.

Off

High availability (HA) is not enabled on this device.

Note

The above LED status descriptions are for an Active/Passive
configuration. In an Active/Active configuration, the HA LED only
indicates HA status for the local device and does not indicate HA
connectivity of the peer. If HA is active on the given device the LED is
green; if HA is not active the LED is off.

TMP

(Temp)



Green

Chassis temperature is normal.

Yellow

Chassis temperature is outside the normal tolerance for one or more of
the installed cards.

ALM

(Alarm)

Red

There is a hardware failure, which may include a voltage issue, power
supply/module detected (but not working), fan failure, hard drive failure,
HA failover, or temperature above high temperature threshold.

Off

Device is operating normally.

FAN

Green

All fans are operating normally.

Red

One or more fans have failed on one or both of the fan trays. To find out
which fan tray has a fan failure, check the fan tray LEDs. A red LED on
the fan tray will indicate that one or more fans have failed.

PS

(Power
Supply)

Green

All AC or DC power supplies are operating normally.

Red

One or more AC or DC power supplies has failed.

PWR

STS

HA

TMP

ALM

FAN

PS

LOG

«
...
14
15
16
17
18
...
»

Содержание PA-7050 PAN-AIRDUCT







































































Отзывы:

Нет отзывов

Похожие инструкции для PA-7050 PAN-AIRDUCT

SageGlass 300-1194-001

Бренд: SAINT-GOBAIN Страницы: 2

Бренд: PaloAlto Networks Страницы: 2

Бренд: Watchguard Страницы: 2

FVG318v2 - ProSafe 802.11g Wireless VPN Firewall Switch

Бренд: NETGEAR Страницы: 9

FVS328 - ProSafe VPN Firewall

Бренд: NETGEAR Страницы: 228

Бренд: Excelsecu Data Technology Co., Ltd. Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды