Palfinger ILP 25 Скачать руководство пользователя страница 37

Страница: 37 / 65

ILP 25/33 Installation Manual

Rev. 1.4

- 37 -

12.4

Sub-frame Installation (Optional)

Trailer installations require a sub-frame to be installed prior to installing the liftgate.

Never work under platform without safety supports.

Steps:

1. Sub-Frame: Position the sub-frame channels up against the trailers crossmembers in the orientation

shown below. Weld the sub-

frame channel to multiple crossmembers. Use 3/16” welds to secure the

sub-frame to a minimum of four crossmembers.

Subframe

Channel

30"x14"

Crossmembers

Dimension determines

the distance of the

mount plates.

Trailer Frame

w/Sub-Frame

Channels

3/16"

Sub-frame

Channel

Trailer

Sliding

Rail

Cross

members

Weld to
Multiple

Cross

Members

Rear

Sill

Crossmember

Side View

Tie subframe

to rear Sill

2. Support Plates: Install three support plates per sub-frame channel as shown and secure the plates

with 3/16” welds.

10.50"

Support Plate

Support

Plate

Trailer Rear View

Side View

Mount
Plates

3/16"

3. After installing the sub-frame, follow the installation procedure in Section 12 to complete the liftgate

installation.

Содержание ILP 25


































































Результаты поиска

Содержание ILP 25

Отзывы:

Похожие инструкции для ILP 25

Бренды по названию

Популярные бренды

Palfinger ILP 25, Руководство по установке

Результаты поиска

Содержание ILP 25

Отзывы:

Похожие инструкции для ILP 25

Бренды по названию

Популярные бренды