Palazzetti MULTIFIRE BIO 14, Инструкция по установке, эксплуатации и обслуживанию

Страница: 34 / 144

34
INTRODUCTION
2 SAFETY WARNINGS
2.1 INSTALLATION WARNINGS
C
RPSO\ ZLWK WKH UHTXLUHPHQWV VSHFL¿HG LQ WKLV
manual.
The stove assembly and dismantling instructions
are reserved exclusively for specialist technicians.
Users should always contact our service centre
WR UHTXHVW ZRUN WR EH SHUIRUPHG E\ TXDOL¿HG
technicians. Before having work performed by
other technical personnel verify their effective
technical competence.
Responsibility for work carried out in the place
where the stove is installed lies with the user;
the user is also responsible for making sure the
installation checks are completed.
The user must abide by all local, national and
European safety requirements.
7KH DSSOLDQFH PXVW EH LQVWDOOHG RQ ÀRRUV ZLWK D
suitable load-bearing capacity.
Make sure that the flue and air intake duct
arrangements correspond to the type of installation.
Do not make any electrical connections using
temporary or uninsulated cables.
Make sure the electrical system is earthed
correctly.
Before starting to assemble or dismantle the stove,
the installer must heed the safety precautions
UHTXLUHGE\ODZVSHFL¿FDOO\
A) do not work in adverse conditions;
B)
DOZD\V EH LQ D ¿W PHQWDOSK\VLFDO VWDWH
for working and make sure that personal
protective equipment is in perfect working
order;
C) always wear safety gloves;
D) always wear safety shoes;
E) always use electrically insulated tools;
F) make sure that the area being used for
assembly and dismantling is clear of any
obstacles.
2.2 MAINTENANCE WARNINGS
&RPSO\ ZLWK WKH UHTXLUHPHQWV VSHFL¿HG LQ WKLV
manual.
‡
Use always personal protective equipment and
other means of protection.
‡
Before starting any maintenance work make
sure that the stove, if it had been operating, has
cooled down.
‡
If even just one of the safety devices is not
calibrated or not working, the stove must be
considered out-of-service.
‡
Disconnect power before working on electrical
or electronic parts and connectors.
2.3 WARNINGS FOR THE USER
Prepare the stove installation site in accordance
with local, national and European regulations.
‡
As the stove is a heating appliance it has very
hot outside surfaces. For this reason maximum
FDUHPXVWEHSDLGGXULQJRSHUDWLRQVSHFL¿FDOO\
‡
do not touch or get too close to the glass door to
avoid getting burned;
‡ GRQRWWRXFKWKHÀXH
‡
do not perform any type of cleaning;
‡
do not remove the ash;
‡
do not open the glass door, except when loading
wood;
‡
never place any objects on top of the stove;
‡
do not open the ash bin (where featured);
‡
make sure children keep away from the stove.
‡ &RPSO\ ZLWK WKH UHTXLUHPHQWV VSHFL¿HG LQ WKLV
manual.
‡
Follow the instructions and warnings highlighted
RQWKHPHWDOODEHOVDI¿[HGWRWKHVWRYH
‡
These labels are safety devices, therefore they
must always be perfectly legible. If damaged or
illegible they must be replaced, contacting the
manufacturer for an original spare label.
‡ 2QO\ XVH IXHO FRPSOLDQW ZLWK WKH VSHFL¿FDWLRQV
shown in the corresponding chapter of this
manual.
‡
Strictly follow the routine and special
maintenance plan.
‡ 'R QRW XVH WKH VWRYH ZLWKRXW ¿UVW KDYLQJ
SHUIRUPHG WKH GDLO\ LQVSHFWLRQ DV VSHFL¿HG LQ
the chapter on “Maintenance” in this manual.
‡
Do not use the stove in the event of malfunctions,
suspected breakage or unusual noises.
‡
Do not pour or spray water onto the stove when
RSHUDWLQJRUWRH[WLQJXLVKWKHÀDPHLQWKHEXUQ
pot.
‡
Do not switch the stove off by unplugging the
power cord.
‡
Do not rest your weight on the open door as this
may affect stability.
‡
Do not use the stove in any way as a support or
anchor.
‡
Do not clean the stove until the structure and
ash have completely cooled down.
‡
Touch the door only when the stove has cooled
down.
‡
Perform all operations without haste, in such a
way as to ensure maximum safety.
‡ ,QWKHHYHQWRI¿UHLQWKHFKLPQH\VZLWFKWKHVWRYH
off using the procedure described in this manual,
DQGZKHUHQHFHVVDU\FDOOWKH¿UHGHSDUWPHQW
‡ ,QWKHHYHQWRIVWRYHPDOIXQFWLRQVGXHWRÀXHV
ZLWKLQFRUUHFWGUDXJKWFOHDQWKHÀXHDFFRUGLQJ
to the procedure described in this manual.
‡
Do not touch the painted parts during operation
to avoid damaging the paintwork.