Pacific S-20 Скачать руководство пользователя страница 7

Страница: 7 / 57

MACHINE PREPARATION

SETTING THE DIP SWITCHES ON YOUR ON-BOARD CHARGER FOR YOUR BATTERY TYPE

Both the on-board and off-board chargers are able to charge wet, lead acid or maintenance-free AGM batteries. As

your unit leaves Pacific Floorcare’s factory, the charger is set up to match the type of battery chosen in the original

machine order. Should you choose to change from the original battery type, the charger can be changed by re-setting
the dip switches.

NOTE:

The on-board charger has been programmed to work with the batteries that Pacific Floorcare provides. Using

other battery types not specified for the S-20 by Pacific Floorcare may impair performance of the unit and will affect

the life of the batteries.

To access the dip switches, use a small screw driver to lift the corner of the label on the on-board charger and peel back

partially to reveal them. Set the dip switches as shown below for the specific battery type being used in your machine.

Use small screw driver
to lift label off charger

BATTERY

PART NUMBER

DIP SWITCHES

(TOP TO BOTTOM)

BATTERY

DESCRIPTION

851303

OFF

TROJAN 155AH

LEAD ACID

881350

OFF

TROJAN OR

CROWN 130AH

LEAD ACID

841311

FULL RIVER

140AH AGM

851302

OFF

FULL RIVER

105AH AGM

Содержание S-20


























































Результаты поиска

Содержание S-20

Отзывы:

Похожие инструкции для S-20

Бренды по названию

Популярные бренды

Pacific S-20, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание S-20

Отзывы:

Похожие инструкции для S-20

Бренды по названию

Популярные бренды