background image

14

MACHINE PREPARATION

CONNECTING THE SQUEEGEE AND ADJUSTING SQUEEGEE HEIGHT

Prior to shipping from the factory, the squeegee assembly is removed from the unit.  To connect your squeegee assembly to the machine: 

Positioning the squeegee assembly to 

mount onto the squeegee frame

The squeegee blade assembly height is factory set at the optimum water recovery position with the squeegee wheels being  

approximately 1/32 inch (1 mm) off the ground allowing the recovery blade to deflect as shown below. 

Thumb screw to raise and lower 

squeegee assembly wheels

After aligning assembly, tighten the 

easy-grip knobs and attach the  

recovery hose.

*Arrows indicate proper hose routing 

Align the squeegee assembly retention slots with the easy-grip 
knobs then tighten until secure.  

Attach the recovery hose to the squeegee assembly neck.  Make 
sure to route the loop hose trap between the squeegee  
assembly neck and left easy-grip knob.

Close up of squeegee assembly and 

blade deflection 

Proper recovery 

blade deflection

Slight clearance 

off of floor

No clearance 

off of floor

1

2

3

4

1

2

3

4

If for some reason your squeegee blade height must be adjusted, it is done so by turning the left thumb screw located on the squeegee 
frame assembly clockwise to raise the left squeegee wheel and counter-clockwise to lower the wheel.  The same is true for the right 

thumb screw/squeegee wheel. 

Содержание S-20


























































Отзывы: