SECTION 3 INSTALLATION
63
3.4
OUTPUT POWER CONNECTION
The connection of the load to the output of the AMX-Series Power Source is described in this
section.
3.4.1 SINGLE PHASE OUTPUT
The wiring requirements for a low range ( 0-135, 0-150 V
AC
) single phase load are shown in
Figures 3.4.1.1 and 3.4.1.2.
The output power is taken from the terminal block located on the rear panel of the chassis
labeled "
OUTPUT POWER
." The Output Form is set for
FORM 1
when this type of load is
attached.
The high side of the load is connected to the "
1
φ
" terminal (the "
L1
" terminal on the Model
125-AMX) when making connections to an AMX-Series Power Source. The "
N
" ( "
L2
"
terminal on the Model 125-AMX) terminal is the low side of the output. The low side of the
load connects to this terminal in all models.
The "
CHS
" terminal
must always
be connected to the chassis of the load. Since the output
is isolated, either output terminal (
direct-coupled output only
) may be connected to chassis.
This allows the user to re-establish a local ground for the output. The output must be refer-
enced to chassis somewhere, preferably neutral. Unless demanded otherwise by a par-
ticular application, Pacific Power Source recommends that a jumper be installed across the
"
N
" ("
L2
" for Model 125-AMX) and "
CHS
" terminals of the Output Terminal block.
The "
N
" terminal of the Output Power Terminal Block
must always
be connected to the
"
CHS
" terminal when using transformer-coupled outputs. Refer to Paragraph 3.4.4 for
special considerations when using transformer-coupled output forms.
Refer to Paragraph 3.7 for connection of the External Sense Input, when used.
NOTE:
It is the user's responsibility to meet all local and national electrical
codes when installing this equipment.
WARNING
LETHAL VOLTAGES ARE PRESENT AT THE OUTPUT TERMINALS OF THIS MACHINE !
REFER OUTPUT CONNECTION TO A QUALIFIED ELECTRICIAN.
Содержание AMX Series
