background image

 

 

 

OWNER’S 

INFORMATION 

Sectio

n

 2

 

Congratulations on your purchase of a Pacific Energy Gas Fireplace. 

Your fireplace has been professionally installed by: 

Dealer name: ___________________ 

Phone Number: _________________ 

If you discover any problems with your gas fireplace contact your dealer immediately to have the 
unit repaired. 

Caution: Do not attempt to repair the fireplace because you may cause injury to yourself or other, 
and risk causing damage to the unit. 

Before operating your fireplace carefully read this manual and pay close attention to all Safety 
Warnings. The manual contains important information on the unit’s safe operation and 
maintenance. 

When lit for the first time, the fireplace will emit a slight odour for a couple of hours. This is due to 
the  curing  of  paints,  sealants,  gaskets,  and  lubricants  used  in  the  manufacturing  process.  This 
condition is temporary. Open doors and windows to ventilate the area. Odour caused by the curing 
process may cause discomfort to some individuals. 
 
It  is  normal  for  fireplaces  fabricated  from  steel  to  give  off  some  expansion  and/or  contraction 
noises  during  the  start  up  or  cool  down  cycle.  Similar  noises  are  found  with  your  furnace  heat 
exchanger or cook stove oven. 

 

                   First Fire 

Содержание Gmir.Bodya

































Отзывы: