Pacific energy Gmir.Bodya Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 32

Pacific energy Gmir.Bodya Скачать руководство пользователя страница 25

25

INSTALLER

INFORMATION

Burner Tray Installation / Removal

Installation

Place the burner tray in the firebox so that the
venturi is over top of the orifice. To secure the
burner tray, insert the 4 screws using a
screwdriver, as seen in Figure 29.

Removal

Remove the 4 screws seen in Figure 29 using a
screwdriver, and remove the burner tray.

Figure 29: Burner Tray

Glass Kit Installation

To install the glass, evenly spread a thin layer of
crushed glass across the entire burner pan as seen
in Figure 30.

Figure 30: Glass Installation

Log Set Installation

1.  Position rear log against the back firebox as seen in pane 1 of Figure 31.
2.  Interlock right log with rear log as seen in pane 2.
3.  Lean left log against log set as seen in pane 3.
4.  Interlock front log with left log to complete log set structure.

Note: Do Not Block Pilot With Logs

Figure 31: Log Set Installation

Burner Kit Installation / Removal

«
...
23
24
25
26
27
...
»

Содержание Gmir.Bodya

































Отзывы:

Нет отзывов