Pace Technologies PICO 155S Скачать руководство пользователя страница 27

Страница: 27 / 54

Please read this instruction manual carefully and follow all installation, operating and safety guidelines.

PICO-155S Precision Saw

NSTRUCTION

ANUAL

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲

3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: [email protected] W eb: http://www.metallographic.com

6.0 Trouble Shooting

More extensive trouble shooting, repair guides, videos, parts list are
provided online at

www.metallographic.com

Or give us a call at 520-882-6598 with any questions

Problem

Cause

Solution

No power or
function

a. Unit is disconnected from

main electrical power
supply.

b. Main power switch is off.

c. Emergency stop button

engaged.

d. Magnetic switch not

engaged.

e. Shut off switch engaged.

f. Loose of broken wire.

g. Unable to determine

problem.

a. Verify electrical source and

connection.

b. Turn on main power

switch.

c. Release by turning

clockwise.

d. Close hood or wiggle hood

in closed position.

e. Lift specimen holder arm

or turn up shut off screw.

f. Disconnect power and

open up back panel.
Check for any loose or
broken wires

g. Contact service technician

Main motor
does not
operate

a. Hood not closed.

b. Overload activated (error

E1).

c. Transformer switch not

set to the correct voltage.

a. Close hood.

b. Press stop button and then

start button.

c. Set switch to correct
voltage.

Содержание PICO 155S























































Результаты поиска

Содержание PICO 155S

Отзывы:

Pace Technologies PICO 155S, Инструкция по эксплуатации, Страница: 27 / 54

Результаты поиска

Содержание PICO 155S

Отзывы: