Pace Technologies PICO 155S Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 54

background image

Please read this instruction manual carefully and follow all installation, operating and safety guidelines.

7

PICO-155S Precision Saw

I

NSTRUCTION

M

ANUAL

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲

3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: [email protected] W eb: http://www.metallographic.com

2.3.2 Installation - Micrometer

1. For easier installation, retract

micrometer adjustment arm - do
not force movement beyond limits
as this may damage the
micrometer.

2. Loosen bolts on sample support

arm and slide smaller diameter side
of micrometer shaft into outer shaft
guide. DO NOT tighten bolts on
sample support arm at this point.

3. Push micrometer into the outer shaft

guide thus pushing the micrometer
shaft into the machine.  While
holding micrometer in place tighten
set screw on outer shaft guide.
NOTE:  The hole in the micrometer
does not need to line  up with the
bolt and DO NOT over tighten the
bolt as this may damage and pinch
the micrometer.

4. Attached sample fixture to sample

support arm and then align holder
to approximately where the
wafering blade will be installed.
Tighten sample holding arm bolts

Retract micrometer arm

Slide smaller end of
micrometer shaft into outer
shaft guide

Tighten set screw
- DO NOT OVER
TIGHTEN as this
may damage
micrometer

Install sample
fixture, align
sample support
arm and then
tighten bolts

«
...
9
10
11
12
13
...
»

Содержание PICO 155S























































Отзывы:

Нет отзывов

Похожие инструкции для PICO 155S

Бренд: KAKA Industrial Страницы: 25

Бренд: Selco Страницы: 94

Бренд: Tanaka Страницы: 16

Бренд: Nakayama Страницы: 19

Бренд: Zenit Powertools Страницы: 10

Бренд: TYROLIT Hydrostress Страницы: 17

Бренд: Scheppach Страницы: 88

Бренд: Jet Страницы: 32

Бренд: F.F. Group Страницы: 68

Бренд: Meec tools Страницы: 30

Бренд: Meec tools Страницы: 49

Бренд: inventiv Страницы: 44

Бренд: HOLZMANN MASCHINEN Страницы: 85

Бренд: HOLZMANN MASCHINEN Страницы: 87

Бренд: ATIKA Страницы: 192

Бренд: Logan Graphic Products Страницы: 10

Бренд: Scheppach Страницы: 17

Бренд: Scheppach Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды