Pace Technologies PICO 155S Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 54

Pace Technologies PICO 155S Скачать руководство пользователя страница 25

Please read this instruction manual carefully and follow all installation, operating and safety guidelines.

21

PICO-155S Precision Saw

I

NSTRUCTION

M

ANUAL

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲

3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: [email protected] W eb: http://www.metallographic.com

17

5.0 Maintenance

5.1

Introduction

The

PICO-155S

wafering saw requires very minimal maintenance. However, to increase the

life of the saw, it is suggested that the cutting fluid be changed regularly (weekly) using a
cutting fluid containing an anti-corrosion additive (e.g DIACUT 2 cutting fluid).

After use it is also recommended that the unit be thoroughly rinsed and dried.

DIACUT oil-
based cutting
fluid

DIACUT 2 anti-
corrosion cutting fluid

Remove and clean
coolant tank- replace
with recommended
cutting fluid

Periodically remove the micrometer shaft and clean any cutting swarf material build up on the shaft.

Remove micrometer
Shaft and clean

Remove micrometer

«
...
23
24
25
26
27
...
»

Содержание PICO 155S























































Отзывы:

Нет отзывов