manualshive.com logo in svg

PAC SR-GM14H, Руководство пользователя, Страница: 3 / 17

Поделиться
Скачать
PAC SR-GM14H Скачать руководство пользователя страница 3

Stinger HEIGH10

 

 Radio Replacement Kit

 for select 2014-2019 Silverado/Sierra Truck   

SR-GM14H

 © 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

Pacific Accessory Corporation

Page 3

Rev: V1

Date: 030121

®

®

Before starting, determine the vehicle’s factory audio system by

referencing the Service Parts Identification sticker inside the 

upper glove box.

The installations are very similar for each type of factory audio 

system, but there are differences referenced throughout this guide.

Note: The installation shown in this guide is IO5 with factory 

rear camera and steering wheel controls.

One of these RPO codes will be listed:

IO3, IO4, IO5, IO6 or IOB

Step 3

Step 2

Step 1

Section 1: Disassembly

Part One: Center Dash Disassembly

If equipped, remove the two 

7mm screws from the CD/DVD 

mechanism, remove and unplug. 

(This plug will not be reconnected).

Remove the four 7mm screws 

securing the radio display/climate 

control panel. Pull outward to 

release the retaining clips.

Remove all connectors from the 

back of the panel. 

Remove the radio display/climate 

control trim panel using a plastic 

trim tool to release the retaining 

clips. Unplug any wire harnesses 

from the back of the trim panel, if 

equipped.

This installation manual will cover the necessary order of procedures to complete the installation 

efficiently and to avoid redoing any steps. The order will be as follows; Disassembly, In-Vehicle Harness 

Connections and Preparation, Interface and Main Harness Connections, Display Mounting Panel 

Preparation, Radio Module Preparation and Radio Unit Installation.

The installation steps shown are all required for full functionality of the radio. If adding additional 

components; cameras, amplifiers, satellite radio, etc., additional steps and harnesses will be needed.

Factory Radio Code

Содержание SR-GM14H


















Отзывы:

Нет отзывов