manualshive.com logo in svg

PAC SR-GM14H, Руководство пользователя, Страница: 16 / 17

Поделиться
Скачать
PAC SR-GM14H Скачать руководство пользователя страница 16

Stinger HEIGH10

 

 Radio Replacement Kit

 for select 2014-2019 Silverado/Sierra Truck   

SR-GM14H

 © 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

Pacific Accessory Corporation

Page 16

Rev: V1

Date: 030121

®

®

Step 5

Step 4

Plug the two display cables into 

the back of the HEIGH10 display. 

Re-connect the factory climate 

control connector to the climate 

controls. 

Place the mounting panel in place 

and temporarily secure it with two 

7mm screws. 

Before reassembly, it is 

recommended to power up the radio 

and check the chime volume* and 

all other functionality...

Volume, Balance, Fade

AM/FM Reception

Bluetooth

USB

Apple Carplay

Android Auto

Camera(s)

* The Chime Module has a 4 

position volume selector on the 

side. Setting 1 being the loudest 

and 4 being the quietest.

Section 5: Radio Unit Installation (cont.)

Part Two: Radio Unit Mounting (cont.)

Firmware Updates (RadioPRO)

The RadioPRO PC app will allow you to update the interface modules with new firmware as it becomes available. 

Please visit 

www.PAC-audio.com/firmware to download available updates.
To update an interface module, open the RadioPRO PC app, connect the interface to your PC via a micro USB cable, and select 

”Firmware” and then “Update Firmware”.

Product Updates (Firmware)

Now, select “Select File”. Finally, browse to the place where you saved the file, and select it. This will begin the updating 

process. Once finished, disconnect the interface from the PC.

Firmware Updates (Stinger Radio and PAC Application APK)

To update the HEIGH10 radio firmware and PAC Application APK firmware, refer to the HEIGH10 product page: 

www.stingerelectronics.com/products/heigh10

Содержание SR-GM14H


















Отзывы:

Нет отзывов