manualshive.com logo in svg

PAC SR-GM14H, Руководство пользователя, Страница: 1 / 17

Поделиться
Скачать
PAC SR-GM14H Скачать руководство пользователя страница 1

Stinger HEIGH10

 

 Radio Replacement Kit

 for select 2014-2019 Silverado/Sierra Truck   

SR-GM14H

 © 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

Pacific Accessory Corporation

Page 1

Rev: V1

Date: 030121

®

®

Introduction and Features

The SR-GM14H is a complete radio replacement kit for the installation of the Stinger HEIGH10

®

 modular radio in Chevrolet 

Silverado and GMC Sierra trucks. All modules, cables and adapters are included to retain important features of the factory system, 

including: OnStar, front and rear park assist, warning chimes, factory reverse camera, steering wheel-mounted radio controls and 

AM/FM reception. Plug & Play wiring harnesses allow for quick and easy installation without the need to cut or splice any wiring. 

The display mounting panel allows flush mounting the 10 inch display without modifying/cutting any part of the vehicle’s sub-dash.

Important Notes

Recommended Tools

We recommend reading this manual thoroughly to familiarize yourself 

with the entire process prior to beginning the installation.

1.  HEIGH10 Display Mounting Panel

2.  Dual USB Extension (SSUSB2)

3.  AM / FM Antenna Adapter (BAA22)

4.  Satellite Antenna Adapter (SAT-01)

5.  Main Harness (SR-GM14H-HAR-A)

6.  Vehicle Side Harness B (SR-GM14H-HAR-B)

7.  Vehicle Side Harness C (SR-GM14H-HAR-C)

8.  Radio Replacement Interface (RP5-GM51)

9.  Steering Wheel Control Harness (GM5LIN-SW-HAR)

10. Factory Rear Camera Adapter (CAM-GM51)

11.  IOB Display Harness (GM5CAM-DIS-HAR)

12.  Chime Module (CMX)

13. 

Differential Video Adapter (RPA-VA1)

Included Components

1

4

6

10

8

5

2

11

3

7

9

12

13

1. Does not retain the following factory features:

2. Not compatible with vehicles equipped with Bose amplified audio system.

3. Please make your vehicle settings selections before removing the factory radio for optimal installation time. Once the radio 

has been removed, the vehicle settings which are normally selected through the factory radio can be accessed and changed 

by downloading and installing the PAC Vehicle Settings program from http://www.pac-audio.com/firmware

4. The Voice button can be set to activate the factory OnStar function when pressed for longer than 1.5 seconds or given

the ability to control the aftermarket radio. This option can be found in the PAC Vehicle Settings program mentioned above in

note three. The default setting for this button is to control the factory OnStar. If this button is set to control the aftermarket radio, 

OnStar can still be accessed by using the mirror controls.

● Factory satellite radio
● Rear seat entertainment system (RSE)
● Steering wheel control backlighting
● Factory USB Ports

Plastic Panel Tool
7mm Socket
10mm Socket

Pick Tool
Wire Feeder

Ratchet
Torx T15 Screwdriver
Small Flat-blade Screwdriver

NOTE: Along with the SR-GM14H components, 

additional hardware and wire harnesses from the 

HEIGH10 (UN1810) kit will also be used in the 

installation. 

Содержание SR-GM14H


















Отзывы:

Нет отзывов