background image

 

Manual 

 

                                                                                                                                     

www.industrisal-needs.com

 

 

 

7.2 

Tips on determining the operation period 

The treatment time depends on various factors, e.g.: 

 

Type of smell 

 

Intensity of smell 

 

Size of the room and temperature 

 

Time and intensity of impact 

 

Composition of the material and source of smell 

 

Spread of smell 

If  you  treat  a  room  that  is  not  heated  at  the  time,  but  will  be  heated  again  after  treatment,  it  might 
lead  to  a  recurrence  of  the  smell.  Thus  the  room  temperature  should  be  kept  during  treatment 
always a little higher than the operation temperature later on (approx.. +5 °C).  

In case the smell reappears after the treatment, you might have chosen a much too short treatment 
time  or  the  room  temperature might  have  been  too  low.  Repeat  the  treatment  by  varying  the  room 
temperature and the treatment time.  
 

Shutdown 

After  the  set  time  is  run  out,  the  device  automatically  switches  into  Standby  mode,  as  mentioned 
above.  

 

The time the treated room needs until the ozone concentration in the air is back to its initial 
non-toxic  state, or reaches the MAK level of 0.1 ppm, depends on various factors like the air 
humidity, the treated material, size of the room, period of treatment etc.  

 

The  treated  rooms  need  to  be  checked  on  their  ozone  concentration  by  trained  and 
authorized personnel, before they become open for access again.  

 

The mean half-life of ozone is 30 min., depending on temperature, air pressure, UV radiation 
etc.  

 

The following calculation can be followed for the determination of the time of regeneration: 
If the air concentration is at the time t =0 at a level of 100 % (e.g. 20 ppm- high value!!), It will 
be 50% after half an hour (10 ppm). After an hour it will be 25 % (5 ppm). After four hours it 
will be only 0.4 %, which equals 0.078 ppm for a relatively high initial air concentration. The 
MAK value is on 0.01 ppm. Thus the room can be accessed after four hours again. 

 

Even  after  four  hours  we  recommend  to  not  access  the  room  before  it  wasn’t  thoroughly 
aerated.  The  regeneration  time  can  be  even  shortened  by  the  aeration.  Always  aerate  the 
treated  room  afterwards.  If  the  room  must  be  accessed  for  aeration,  wear  an  adequate 
mask.  

We recommend waiting at any case at least 4 hours before accessing the room again. 
 

 

Содержание XT - series












Отзывы: